Advertisement
Available languages
Available languages
appliance on a cold wall (an exterior wall)
and below a window. But never obstructing or
covering a ventilation area.
WALL ASSEMBLING:
- Securing to the wall (Fig.2): Use a pencil to
mark the right position to drill the wholes for the
wall plugs (E).
- Make sure the diameter of the wholes corre-
sponds to the diameter of the wall plugs.
- Drill two wholes on the areas previously mar-
ked (Fig.2).
- Insert the wall plugs (E) into the wholes.
- Once the wall plugs have been fitted into
the wall, screw the two screws (D), leaving a
distance of approximately 10mm between the
screw head and the wall.
- Make sure the screws are well fixed before
hanging the appliance.
- Use the wholes behind the appliance to hang it
from the two screwheads.
- Ensure that the appliance is properly and safe-
ly fixed in its working position with the screws.
INSTRUCTIONS FOR USE
BEFORE USE:
- Make sure that all the product's packaging
have been removed.
- Some parts of the appliance have been lightly
greased. Consequently, the first time the ap-
pliance is used a light smoke may be detected.
After a short time, this smoke will disappear.
- To eliminate the smell given off by the applian-
ce when used for the first time, it is recommen-
ded to have it on at full power for 2 hours in a
well-ventilated room.
- Prepare the appliance according to the function
you wish to use:
FIRST-TIME USE:
- Extend the cable completely before plugging
it in.
- Connect the appliance to the mains.
- Before turning on the heater for the first time,
you must set the correct time.
- Press the "LOCK" (VIII) button. The LED dis-
play will show 00:00 and the "MO" (3) light will
turn on. Then you can start setting the time:
- HOURS: Press the "SET" (XII) button once.
The first "00" will start blinking. Use the "+" (XI)
or "-" (VI) buttons to select the correct hour
(1-24h).
- MINUTES: Once you have set the correct
hour, press the "SET" button again. Now the
second "00" will start blinking. Use the "+" (XI)
or "-" (VI) buttons to select the correct minutes
(0-59min).
- DAY: Once you have set the correct minutes,
press the "SET" (XII) button once more. The
"MO" light (3) will start blinking. Use the "+" (XI)
or "-" (VI) buttons to select the correct day of
the week (Mo-Su)
- NOTICE that the numbers on the display will
blink only for 5 seconds. You must operate in
that time. Otherwise the appliance will go back
to standby mode.
GENERAL USE:
- Turn the appliance on, by pressing the on/off
button on the remote control (I).
- The unit will blow cold air and the fan indicator
(1) will turn on.
MODE SET UP:
- Press the "MODE" button (II) once to turn on
heat intensity I (1000W). Indicators 1 and 2 will
turn on.
- Press the "MODE" button (II) a second time to
turn on heat intensity II (2000W). Indicatos 1
and 4 will turn on.
- Press the "MODE" button (II) a third time to go
back to the fan function. Indicator 1 will turn on.
TIMER FUNCTION:
- The appliance's operating time can be control-
led.
- To start this function, press the timer button
(VII).
- Every time you press the timer button (VII), the
time will adjust one hour (0-24h).
- The "D" indicator (9) will turn on.
THERMOSTAT FUNCTION:
- The appliance can be programmed to automa-
tically keep a set temperature.
- To adjust the temperature press the "+" (XI) or
"-" (VI) buttons. The selected temperature will
show on the LED display (13). The temperature
can be set from 10ºC to 49ºC.
- The thermostat indicator (8) will turn on.
- If the room temperature drops 2 degrees below
the set temperature, the heater will start run-
ning at intensity I (1000W).
- If the room temperature drops 4 degrees below
the set temperature, the heater will start run-
ning at intensity II (2000W).
Advertisement
