Taymor ZURICH 06-4301P Installation Instructions

INSTALLATION INSTRUCTIONS
ZURICH 06-4301P
SINGLE HANDLE LAVATORY FAUCET
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1, NSF-61 AND LOW LEAD COMPLIANT
THANK YOU FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
1
RECOMMENDED TOOLS:
Teflon tape Screwdrivers Adjustable
Flashlight
wrench and
pipe wrench
WARNING: READ ALL the instructions completely before beginning.
READ ALL warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help? Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
TURN OFF THE MAIN WATER SUPPLY
2
Locate water supply inlets and shut off water supply valves. These are usually found under
the sink.
TURN OFF
INSTALLING FAUCET WITH SINGLE HOLE MOUNTING
3A
A) Apply a bead of plumber's putty or silicone caulk around the sink opening.
B) Place seat (1) onto the bottom of faucet body. From above sink, insert faucet supply tubes through hole
on sink.
C) From underneath the sink, secure faucet faucet body using washers (1) and nut (2). Secure the nut (2) not
to exceed 1/4 turn, after hand tighten.
A
INSTALLING FAUCET WITH ESCUTCHEON
3B
A) Apply a bead of plumber's putty or silicone caulk around the sink openings.
B) Install the base plate over the three holes in your sink.
C) With the handle and spout facing forward, carefully install faucet supply hoses through the center hole of sink.
Center faucet body onto escutcheon and base plate.
D) From underneath the sink, secure faucet faucet body using washers (1) and nut (2). Secure the nut (2) not
to exceed 1/4 turn, after hand tighten.
A B
Don't use plumber's putty on cultured marble or other composite sinks.
Putty will discolour the sink.
WITH OPTIONAL
ESCUTCHEON
Your installation may require new supply
lines. (Supply lines are not included.)
Torque wrench Safety goggles Plumber's putty
TURN OFF
C
B
1
1
C
ATTACH THE HOT AND COLD SUPPLY LINES
4
Thread the nut (1) on supply line onto outlet of water supply valve (2) and tighten with
wrench. Do not overtighten.
INSTALLING POP-UP DRAIN
5
A) Remove pop-up plunger (A) and flange (B). Screw locknut (C) all the way down. Push
gasket (D) down. Apply silicone to underside of flange (B).
B) Insert body into sink (from underneath). Screw flange onto body. Pivot hole (E) must face
the back of the sink.
C) Tighten locknut (C) and gasket but do not overtighten. Remove pivot ball retaining nut (E).
D) Slide pivot rod (F) into the eye of the pop-up plunger (A). Hand tighten retaining nut.
E) Slide pivot rod (F) through hole in spring clip (G), then through lever strap (H) and back
Silicone caulk
through spring clip.
F) Insert lift rod (I) down through faucet body and then into lever strap (H). Tighten screw (J).
Connect assembly to drain.
A
C
D
A
FLUSHING THE WATER LINES
6
Turn on hot and cold water supplies. Flush water lines for
one minute. Check for leaks. Re-tighten any connections if
necessary, but do not overtighten.
EXPLODED DIAGRAM FOR
7
REFERENCE
MAINTENANCE Your new faucet is designed for
years of trouble-free performance. Keep it looking
new by cleaning it periodically with a soft cloth.
Avoid abrasive cleaners, steel wool and harsh
chemicals as these will dull the finish and void
your warranty.
2
15- LIFT ROD KNOB
16- LIFT ROD
17 - FLANGE
D
1
2
CUSTOMER SERVICE
1
2
B
A
B
B
D
B
E
A
E
H
F
F
G
8 - ESCUTCHEON
9 - BASE PLATE
WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
C
E
C
F
I
J
H
1 - HANDLE
2 - SET SCREW
3 - SLEEVE
4 - BONNET
5 - CONNECTOR
6 - CARTRIDGE
7 - BODY
ASSEMBLY
10 - SEAT
11 - WASHER
12 - RUBBER
WASHER
13 - METAL
WASHER
14 - MOUNTING NUT