Taymor ZURICH 06-4001HS Installation Instructions

INSTALLATION INSTRUCTIONS
ZURICH 06-4001HS
ROMAN TUB FAUCET
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1
THANK YOU FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
1
RECOMMENDED TOOLS:
Teflon tape Screwdrivers Adjustable
Flashlight
wrench and
pipe wrench
WARNING: READ ALL the instructions completely before beginning.
READ ALL warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help? Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
TURN OFF THE MAIN WATER SUPPLY
2
Locate water supply inlets and shut off water supply valves.
These are usually found near water meter.
DECK PREPARATION
3
Drill holes in FINISHED DECK per diagram.
NOTE: This kit is intended for installation up to 1-1/8" thick.
Maximum distance between center of
spout and inside of bathtub is 4-11/16"
(119 mm). Refer to illustration above.
INSTALL THE VALVE SYSTEM
4
A
Remove flange (1) from housing assembly.
1
1
C
Place a flange (1) on each housing assembly.
Thread each flange down until it locks onto
housing assembly.
1
Your installation may require
new supply lines.
(Supply lines are not included.)
Torque wrench Safety goggles Plumber's putty
TURN OFF
TURN OFF
ø
1-3/8"
(35 mm)
ø
1-3/8"
(35 mm)
B
With the housing assembly marked "HOT" on
the left, adjust washers (1) and lock nut (2) to
the bottom of the housing assembly. Insert
the housing assembly through the mounting
holes from the underside of the deck/rim.
1
2
D
From underneath the deck secure housing
assembly with lock nut (3) and washers (2).
Wrench tighten locknut (3).
2
TORQUE 3
11 - 15 FT/LBS.
TORQUE
11 - 15 FT/LBS.
HANDLE INSTALLATION
5
Thread handle seat (1) onto flange (2) and secure with set screw (3). Install handle (4)
onto inverter (5) and secure with set screw (6). Insert the index (7).
SPOUT INSTALLATION
6
A
Silicone caulk
Place the flange (1) onto the bottom of the
spout assembly (2). Place spout assembly
(2) through mounting hole in deck/rim.
C
Thread T-tube (1) onto spout shank (2) until it
is completely seated.
HOSE GUIDE INSTALLATION
7
ø
1-3/8"
(35 mm)
A
Insert hose guide (1) into deck hole.
ø
1-1/8"
(29 mm)
C
Connect the flexible water supply hose (1) to the bottom of valve bodies (2) as shown. Aligh T-tube (3)
in a position which will allow maximum clearance to connect hoses. Carefully bend the hoses to fit
available space. Carefully thread hose couplings to the sides of the T-tube (3).
2
11 - 15 FT/LBS
CUSTOMER SERVICE
3
1
5
2
B
From underneath the deck, secure spout
assembly with locknut (2) and washers (1).
Wrench tighten lock nut (2).
2
1
TORQUE
11 - 15 FT/LBS.
B
From underneath the deck, secure hose
guide with rubber washer (1), metal wash-
er (2) and locknut (3). Tighten locknut (3)
securely with wrench.
1
3
TORQUE
1
1
WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
4
6
7
1
2
TORQUE
11-1 5 FT/LBS
1
2
TORQUE
3
11 - 15 FT/LBS.
2
TORQUE
11 - 15 FT/LBS