Graco PR70 Repair Parts
  1. Manuals
  2. Brands
  3. Graco Manuals
  4. Dispenser
  5. PR70 Series
  6. Repair parts
Graco PR70 Repair Parts

Graco PR70 Repair Parts

Two component liquid dispensing systems
Hide thumbs Also See for PR70:
Table of Contents

Advertisement

Quick Links

Download this manual
Repair - Parts
PR70 and PR70v
Two Component Liquid Dispensing Systems
Fixed or variable ratio systems. For accurate metering, mixing, and dispensing of
two-component materials.
3000 psi (21 MPa, 207 bar) Maximum Working Pressure
100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure
Important Safety Instructions
Read all warnings and instructions in all sup-
plied manuals. Save these instructions.
PR70v Shown with Advanced Display Module
312760A
ti12385a

Advertisement

Table of Contents
loading

Related Manuals for Graco PR70

Summary of Contents for Graco PR70

  • Page 1 Repair - Parts PR70 and PR70v 312760A Two Component Liquid Dispensing Systems Fixed or variable ratio systems. For accurate metering, mixing, and dispensing of two-component materials. 3000 psi (21 MPa, 207 bar) Maximum Working Pressure 100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure...

  • Page 2: Table Of Contents

    Fixed Ratio Drive Block Assembly, LC0107 . . . 37 Graco Information ......72 Variable Ratio Base, LC0242, LC0243, LC0244, LC0245 .

  • Page 3: Supplied Manuals

    Supplied Manuals Supplied Manuals PR70 and PR70v Manuals Part Description 312759 PR70 and PR70v with Advanced Display Module Operation and Maintenance Manual 312760 PR70 and PR70v with Advanced Display Module Repair and Parts Manual MD2 Dispense Valve Manual Part Description...

  • Page 4: Product Configurator

    PR70B - J - A5 - A5 - E - A6 - A6 - 3 - 1 - 2 - A - N - 3 - N - H - N - 6 - N - Y - N Code: The following part number fields apply for the PR70 and PR70v part numbering configurator fields. Shaded items listed in the configurator table below are “Super Standard” items that are typically stocked and provide the best deliv- ery dates.
  • Page 5 Product Configurator Custom Low Volume side, consult fac- tory (stainless steel only) Code F Part Controls LC0274 Advanced Display Module with 1 Fluid Control Module LC0275 Advanced Display Module with 2 Fluid Control Modules LC0298 Standard Display Module Codes G-H, High Volume Hose / Part Low Volume Hose...
  • Page 6 Product Configurator LC0169 Recirculating, On-Board Tanks, LC0197 Recirculating, Heated, On-Board 3/8 in. (9.5 mm) - 15 ft (4.6 m) Tanks, 1/2 in. (13 mm) - 10 ft (3.0 m) LC0170 Recirculating, On-Board Tanks, LC0198 Recirculating, Heated, On-Board 1/2 in. (13 mm) - 2.5 ft (0.6 m) Tanks, 1/2 in.
  • Page 7 Product Configurator LC0157 8 L, Twin Polyethylene Tanks and Lids, Code M Part Applicator Mounting Two Pneumatic Agitator LC0294 None, Customer Mount Controls and LC0158 8 L, Twin Polyethylene Tanks and Lids, Applicator One Pneumatic Agitator, with Shut-Off LC0292 Mast Mount, Controls & MD2 Applica- Valves tor Machine Mounted LC0159...
  • Page 8 Product Configurator LC0237 7.5 L, Stainless Steel, High Level Sen- Code Q Part High Volume Side Tank Cover sors, LC0018 On-Board Dust Cover 240V Heat LC0019 On-Board Clamp Down LC0238 7.5 L, Stainless Steel, High Level Sen- LC0020 On-Board Vacuum De-gas sors, LC0021 On-Board Agitate 120VAC 50/60 Hz...
  • Page 9 Off-Board Tank Stands Refill Logic None LC0281 7.5 L Stainless Steel - Low Level Sen- LC0103 PR70 Tank Stand sors Only, and 30 L or 60 L Stainless LC0247 PR70v Tank Stand Steel - Low Level Sensors Only LC0286 7.5 L Stainless Steel - Low Level Sen-...

  • Page 10: Warnings

    Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.
  • Page 11 Warnings WARNING FIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion: • Use equipment only in well ventilated area. • Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc).
  • Page 12 Warnings 312760A...

  • Page 13: Grounding

    Grounding Grounding machine. It is the yellow tab at the left, rear of the machine. The hole in the tab should be visible. 6. If necessary, run a lock through the hole to lock the tab in place. This prevents the system air pressure from being inadvertently enabled.

  • Page 14: Troubleshooting

    Troubleshooting Troubleshooting Before starting any troubleshooting procedures, perform 3. Allow the machine to cool if the machine has a heat the following procedure. control option. Try the recommended solutions in the order given for 1. Relieve pressure. See Pressure Relief Procedure, each problem to avoid unnecessary repairs.
  • Page 15 Troubleshooting Problem Cause Solution Material dispensed not correct weight Specific gravity of one or more of the Recalibrate machine. two materials has changed since cali- bration Machine air pressure has changed Readjust air pressure regulator to since calibration. value used when machine was cali- brated, or recalibrate machine.

  • Page 16: Error Codes

    Troubleshooting Error Codes Code-Class-Event System Shown on Errors Screen Description Behavior Ref 050X-A-Improper System Cal Improper Calibration 06CX-A-Invalid Key Token No or Invalid Key Token A401-A-Over Current Z1 Heater Over Current, Zone #1 A402-A-Over Current Z2 Heater Over Current, Zone #2 A403-A-Over Current Z3 Heater Over Current, Zone #3 A404-A-Over Current Z4...
  • Page 17 Troubleshooting Code-Class-Event System Shown on Errors Screen Description Behavior Ref L2BX-D-Low Level Tank B Low Material Level, Tank B L2FX-D-Low Level Tank A/B Low Material Level, Both Tanks L8AX-D-Refill Timeout A Auto Refill Failed, A Side L8AX-D-Refill Timeout B Auto Refill Failed, B Side T201-D-Low Material Temp Z1 Material Below Temperature, Zone #1 T202-D-Low Material Temp Z2...
  • Page 18 Troubleshooting Code-Class-Event System Shown on Errors Screen Description Behavior Ref T904-A-Temp Switch Cutoff Z4 Over Temp Switch Open, Zone #4 T9C1-A-Control Shutdown Z1 PCB Over Temperature, Zone #1 T9C2-A-Control Shutdown Z2 PCB Over Temperature, Zone #2 T9C3-A-Control Shutdown Z3 PCB Over Temperature, Zone #3 T9C4-A-Control Shutdown Z4 PCB Over Temperature, Zone #4 WM01-A-Current Fault Z1...
  • Page 19 Troubleshooting System Behavior Reference System Behavior Description When this error is generated, a pop-up with the error-code will be shown. Any auto-sequencing, purge timer or recirculation timer operation in progress will be stopped and the foot switch will be disabled until the error-condition is cleared. The error-code pop-up will be shown until the error condition is cleared.

  • Page 20: Electrical Schematics

    Electrical Schematics Electrical Schematics See F See F See F . 1: Electrical Schematic - Page 1 312760A...
  • Page 21 Electrical Schematics . 2: Electrical Schematic - Page 2 312760A...
  • Page 22 Electrical Schematics . 3: Electrical Schematic - Page 3 312760A...
  • Page 23 Electrical Schematics (Optional External Control Interface) . 4: Electrical Schematic - Page 4 See manual 312759 for Optional External Control Inter- face instructions. 312760A...

  • Page 24: Repair

    Repair Repair HydraCheck Kit Installation 200d 200c 200b 200a ti12437a Torque to 85 in-lb (9.6 N•m). . 5: HydraCheck Installation - Variable Ratio Base 100d 100b ti12436a . 6: HydraCheck Installation - Fixed Ratio Base 312760A...
  • Page 25 Repair Adjust the Adjustment Screw/Cap The following procedure is the same for Fixed and Variable Ratio bases, except where noted. See F 5 and F . 6 for part references. Prepare Machine for Kit Installation 10. Push the drive block (104, AA) forward until resis- 1.

  • Page 26: Air Cylinder Kit Installation

    Repair Air Cylinder Kit Installation ti12490a Torque to 41 in-lb (4.6 N•m). Torque to 350 in-lb (39.5 N•m). Torque to 100 ft-lb (135 N•m). Coat all sliding surfaces with lubricant, part 115982. Apply sealant tape to npt fittings. Prepare Machine for Kit Installation Disassemble the Air Cylinder 1.
  • Page 27 Repair in the blind end block (418) using a long allen 25. Reinstall the hex nuts (103, 100b, 100d) to the cylin- wrench. der rod (420) and torque to 100 ft-lb (135 N•m). See . 9 on page 33. 10. Partially remove the air cylinder by pulling on the cylinder from the back of the machine until the air 26.

  • Page 28: Rear Pump Rebuild Kit Installation

    Repair Rear Pump Rebuild Kit Installation The pump shaft is installed with Krytox. Contact with Krytox can lead to flu-like symptoms. The MSDS for this material is available upon request. ti12491a Torque to 350 in-lb (39.5 N•m). Lube shaft with krytox grease prior to insertion into bearing. Shaft seal (503) must be installed with open side facing the washer (512).
  • Page 29 Repair 6. Remove the shroud (117, 214). See F . 10 on block. This will prevent the threads from damaging page 34 and F . 15 on page 41. the seal (503). 17. Slide the pump shaft through the hole in the bearing Disassemble the Rear Pump Assembly housing.

  • Page 30: Piston/Cylinder Replacement Kit Installation

    Repair Piston/Cylinder Replacement Kit 9. Remove the piston (602) and any front or rear washers (603) from the pump shaft (511). See F Installation 7 on page 28. 10. Clean the washers. Install Cylinder 11. Install the new piston and any front or rear washers. 12.

  • Page 31: Check Valve Rebuild Kit Installation

    Repair Check Valve Rebuild Kit 9. Place the new check valve ball guide (2103) on a bench with the open end up. Install the check valve Installation spring (2102) into the guide. 10. Install the check valve ball (2101) on top of the See Pump Sub-Assembly, LC0112, page 46 for spring (2101).

  • Page 32: Piston Plug Installation

    Repair Piston Plug Installation Fuse Replacement 1802 1801 ti12562a 1. Drain the pump. Fuse Holder • If ball valves are installed, close the ball valves then take several shots. ti12563a • If ball valves are not installed, empty the Fuse holder is located between the tanks.

  • Page 33: Parts

    Parts Parts Fixed Ratio Base, LC0262, LC0263, LC0264, LC0265 100d 100b Torque to 85 in-lb (9.6 N•m). Torque to 350 in-lb (39.5 N•m). Torque to air cylinder shaft to100 ft-lb (135 N•m). ti12436a ti12486a 312760A...
  • Page 34 Parts Fixed Ratio Base, continued 100c 100a Torque to 85 in-lb (9.6 N•m). ti12487a Torque to 350 in-lb (39.5 N•m). Retaining ring must rest against pump body. 117a ti12476a . 10 312760A...
  • Page 35 119 96/0235/98 SCREW, drive, type U, #2 X 3/16 stainless steel 120 255244 SWITCH, foot, assembly 127 * LC0135 MODULE, TOKEN, PR70 * Not shown. ▲ Replacement Danger and Warning labels, tags, and cards are available at no cost. 312760A...

  • Page 36: Fixed Ratio Frame Sub-Assembly, Lc0290

    Parts Fixed Ratio Frame Sub-Assembly, LC0290 2205 2206 2204 2202 2201 2203 2202 2207 ti12572a Apply anti-seize compound (part 073025) to screws. . 11 Part Description 2201 120599 PIN, dowel 2202 120913 SCREW 2203 15K788 FRAME, base, machined 2204 LC0234 SENSOR, assembly 2205 120918...

  • Page 37: Fixed Ratio Drive Block Assembly, Lc0107

    Parts Fixed Ratio Drive Block Assembly, LC0107 2306 2301 2305 2308 2302 2307 2309 2305 2303 2304 ti12573a Apply grease (part 115982) to all internal parts. Tighten retaining nut until alignment rod (2302) cannot be moved. Loosen retaining nut until alignment rod can move side-to-side with no in-and-out movement.
  • Page 38 Parts 312760A...

  • Page 39: Variable Ratio Base, Lc0242, Lc0243, Lc0244, Lc0245

    Parts Variable Ratio Base, LC0242, LC0243, LC0244, LC0245 200d 200c 200b 200a ti12437a Torque to 85 in-lb (9.6 N•m). Torque to 350 in-lb (39.5 N•m). Torque to air cylinder shaft to100 ft-lb (135 N•m). ti12488a Torque to 85 in-lb (9.6 N•m). .
  • Page 40 Parts Variable Ratio Base continued 214a ti12475a . 14 Part Description Part Description 61/2906-BK/1 HOSE, 0.245ID x 0.375 OD, PU, 95 200a 120920 SHOCK ABSORB, adjustable (models LC0243 and LC0245 only) LC0246 SHIELD, assembly 200b 111260 SCREW, set, cup point ▲15M511 214a LABEL, shield...

  • Page 41: Variable Ratio Frame Sub-Assembly, Lc0232

    Parts Variable Ratio Frame Sub-Assembly, LC0232 2406 2409 2430 2409 2404 2404 2406 2409 2416 2417 ti12568a 2436 2427 2415 2405 2401 2426 2418 ti12569a 2432 Drive Block Rear Parts Torque screws to 140 in-lb (15.8 N•m). Torque to 8 in-lb (0.9 N•m). Torque screws to 350 in-lb (39.5 N•m).
  • Page 42 Parts Variable Ratio Frame Sub-Assembly continued 2407 2424 2410 2425 2425 2435 2413 2403 2429 2421 2402 2414 2434 2419 2413 2412 2421 2420 2411 2403 2422 2424 2412 2407 Drive Block Front/Side Parts ti12571a 2428 2414 2423 2435 2425 2425 2411 Torque screws to 140 in-lb (15.8 N•m).
  • Page 43 Parts Part Description 2421 15K868 WASHER, female, male modi- Part Description fied, assembly 2401 119912 SCREW, machined, phillips 2422 15T377 BAR, ratio, beam pan head 2423 15T383 PIN, pivot, beam, ratio 2402 107596 SCREW, cap, hex head 2424 15T384 PLATE, guide, ratio 2403 116193 PIN, dowel, 1/4 x 3/4...

  • Page 44: Air Cylinder, Lc0110, Lc0111, Lc0230, Lc0231

    Parts Air Cylinder, LC0110, LC0111, LC0230, LC0231 ti12490a Torque to 41 in-lb (4.6 N•m). Torque to 350 in-lb (39.5 N•m). Torque to 100 ft-lb (135 N•m). Coat all sliding surfaces with lubricant, part 115982. Apply sealant tape to npt fittings. 312760A...
  • Page 45 Parts Part Description 121022 FITTING, elbow, male, 1/4 npt Part Description 15K790 TUBE, air, cylinder, 3.0 (assem- 107571 PACKING, o-ring blies LC0110 and LC0230 only) 114100 SCREW, cap, socket hd 15K789 TUBE, air, cylinder, 4.5 (assem- 120875 O-RING blies LC0111 and LC0231 only) 120880 SCREW 15K791...

  • Page 46: Pump Sub-Assembly, Lc0112

    Parts Pump Sub-Assembly, LC0112 The pump shaft is installed with Krytox. Contact with Krytox can lead to flu-like symptoms. The MSDS for this material is available upon request. ti12491a Torque to 350 in-lb (39.5 N•m). Lube shaft with krytox grease prior to insertion into bearing. Shaft seal must be installed with open side facing away from washer (512).

  • Page 47: Control Bracket, Lc0240, Lc0261

    Parts Control Bracket, LC0240, LC0261 2513b 2513a 2510 2508 2507 2506 2512 2511 2509 2505 2502 2501 2503 2504 ti12568a Assembly LC0240 Shown Apply thread sealant tape to male npt threads. Part Description Part Description 2507 289697 BASE, Fluid Control Module 2501 15T735 BRACKET, control mounting 2508 121583 HARNESS, I/O, M12 x M8 x sub- (assembly LC0240 only)

  • Page 48: Incoming Power Bracket, Lc0239

    Parts Incoming Power Bracket, LC0239 320, 327 320, 327 306, 318 ti12489a Apply thread sealant tape if applicable. 312760A...
  • Page 49 Parts Ref Part Description 316 94/0762/99 VALVE, safety, blow-off, 100 Ref Part Description 301 119912 SCREW, mach. phillips pan 317 94/0387/99 PLUG, pipe, 1/4 npt 318 81/1054-4/11 FUSE, type f, 4 amp, 250v, 302 121018 FITTING, elbow, male, fast swivel, 1/4 npt 319 LC0291 CABLE, power, assembly 303 120876...

  • Page 50: Piston Package

    Parts Piston Package ti12438a Arrow on cylinder points to the o-ring (606) on the right. Nylon Piston Assemblies Reference Number and Description Piston Tube, Nylon Ring, support, Package pump Piston Washer piston Screw O-ring LC1080 LCC080 LCB080 15M089 LC1100 LCC100 LCB100 15M089 LC1120...
  • Page 51 Parts UHMW Piston Assemblies Reference Number and Description Piston Tube, UHMW Ring, support, Package pump Piston Washer piston Screw O-ring LC2160 LCC160 LCA160 LC2180 LCC180 LCA180 LC2200 LCC200 LCA200 LC2220 LCC220 LCA220 15M099 15K887 LC2240 LCC240 LCA240 LC2260 LCC260 LCA260 LC2280 LCC280 LCA280...

  • Page 52: Controls

    Parts Controls Fluid Control Module There are three options for controls. 705b • Advanced Display Module with one Fluid Control Module, LC0274 • Advanced Display Module with two Fluid Control 705a Modules, LC0275 • Standard Display Module, LC0298 ti12711a Part Description 289697 MODULE, base 277674 ENCLOSURE, door...

  • Page 53: Applicator Mounting

    Parts Applicator Mounting ti12439a Part Description Part Description 15U176 CLAMP, base (assemblies 15K836 BASE, arm, mounting 256438 and LC0293 only) 15K833 ARM, mounting, twnmxr (assem- 120908 WASHER, plain M8 (assemblies blies 256439 and LC0292 only) 256438 and LC0293 only) 15K866 ARM, mounting, HMI only 96/0045/98 WASHER, lock, split, 5/16 in.,...

  • Page 54: Dispense Valve

    Parts Dispense Valve Standard Dispense Valves, 255179 and 277181 See MD2 Dispense Valve manual referenced at the beginning of this manual. Gun Mounted MD2 Valves, LC0120 and LC0122 901a 902b Assembly LC0120 Shown ti12440a Part Description LC0006 VALVE, assembly, 10:1, gun, electric (assembly LC0122 only) LC0004 VALVE, assembly, 1:1, gun, electric...
  • Page 55 Parts Dispense Valve Handle, Part 255208 1018 1017 1019 1012 1011 1010 1007 1008 1015 1009 1014 1016 1013 1006 1001 1004 ti12477a 1002 1003 1005 Apply lubricant, part 070272. Torque to 20-30 in-lb (2.3-3.4 N•m) Press fit pin to bottom. Torque to 125-135 in-lb (14.1-15.2 N•m) Torque to 15-20 in-lb (1.7-2.2 N•m) Part...
  • Page 56 Parts Lever Actuated MD2 Valves, LC0121 and LC0123 1101a 1101b 1103 1102 Assembly LC0121 Shown ti12441a Part Description 1101 LC0005 VALVE, assembly, 1:1, lever, electric (assembly LC0121 only) LC0007 VALVE, assembly, 10:1, lever, electric (assembly LC0123 only) 1101a 255249 LEVER, 2K dispense valve 1101b †...
  • Page 57 Parts Dispense Valve Lever, Part 255249 1202 1213 1203 1212 1214 1204 1201 1208 1207 1215 1203 1206 1209 1217 1210 1211 1205 1216 Apply adhesive 070269 to threads. Torque to 15-20 in-lb (1.7-2.2 N•m) Torque to 20-30 in-lb (2.3-3.4 N•m) ti12485a Part Description...

  • Page 58: Mixers

    Parts Mixers 1301 1303 1302 Assembly LC0061 Shown ti12442a Reference Number and Description 1301 1302 1303 Mixer Package Description Mixer Shroud Sleeve LC0057 1/4 in. X 24 60/0204/50 94/0883-C/98 LC0058 3/8 in. x 24 60/0200/50 94/0883-D/98 LC0059 3/8 in. x 36 60/0201/50 94/0883-E/98 LC0060...

  • Page 59: Hose Packages

    Parts Hose Packages Unheated, Non-Recirculating Hoses 1404 1403 1401 1402 Assembly LC0801 Shown ti12446a Apply thread sealant tape to male npt threads before assembly. Reference Number and Description 1401 1402 1403 1404 Hose Package Description Hose Assembly 90 Deg Elbow Adapter Bushing LC0801...
  • Page 60 Parts Unheated, Recirculating Hose Packages 1603 1602 1603 1602 1601 Assembly LC0161 shown installed as the Low Volume and High Volume Side Hose Package 1601 ti12444a Apply thread sealant tape to male npt threads before assembly. Dispense valve shown for reference only. Reference Number and Description 1601 1602...
  • Page 61 Parts Reference Number and Description 1601 1602 1603 Hose Valve Supply Hose Return Hose Package Description Assembly Assembly Assembly LC0174 3/4 in. x 180 in., on-board 255974 255996 258068 LC0175 3/16 in. x 30 in., off-board 255977 255983 258069 LC0176 3/16 in.
  • Page 62 Parts Heated, Recirculating Hose Packages 1703 1702 1703 1702 1701 Assembly LC0190 shown installed as the Low Volume and High Volume Side Hose Package ti12443a 1701 Apply thread sealant tape to male npt threads before assembly. Dispense valve shown for reference only. Reference Number and Description 1701 1702...
  • Page 63 Parts Reference Number and Description 1701 1702 1703 Heated Insulated Hose Valve Supply Hose Return Hose Package Description Assembly Assembly Assembly LC0200 3/4 in. x 180 in., on-board 255974 258094 258126 LC0201 1/4 in. x 30 in., off-board 255976 258084 258127 LC0202 1/4 in.
  • Page 64 Parts Heated, Non-Recirculating Hoses 1503 1504 1501 1502 Part LC0881 Shown ti12445a Apply thread sealant tape to male npt threads before assembly. Reference Number and Description 1501 1502 1503 1504 * 1505 * 1506 Heated Hose 90 Degree 45 Degree Circuit Extension Hose Package Description...

  • Page 65: Power Cords

    Parts Power Cords Check Valve, Assembly LC0093 2104 2101 ti12447a 2102 Part 121054 Shown ti12565a 2103 Power The side of seat with chamfer must point away from ball. Cord Package Description 121054 CORD SET, 250V, 10A, United States Part Description 121055 CORD SET, 250V, 10A, North America 2101 105445...

  • Page 66: Tank Stands, Assemblies Lc0247 And Lc0103

    Parts Tank Stands, Assemblies Heat Zone Assemblies LC0247 and LC0103 See Integrated Heat manual referenced at the beginning of this manual for Heat Zone Assemblies parts informa- tion. 2001 2002 ti12473a Assembly LC0247 Shown Part Description 2001 121097 FASTENER, u-bolt with mounting plate 2002 15U373 SUPPORT, tank stand, variable ratio (assembly LC0247 only)

  • Page 67: Kits

    Kits Mixer and Shroud Options Machine Rebuild Kits Part Description See the PR70 and PR70v Repair - Parts manual LC0063 Mixer, 3/16 in. (6.5 mm) x 32, 10 Mixers referenced at the beginning of this manual for parts with shroud included in each kit.
  • Page 68 Kits Vacuum Kits Refill Kits These vacuum kits contain the parts necessary to Refill Kits 256659 and 256660 are designed to turn on attach a vacuum pump to the tanks. and off a transfer pump as needed to keep the tanks at the proper fluid level.

  • Page 69: Dimensions

    Dimensions Dimensions Machine with On-Board Tanks ti12621a ti12622a PR70 † Assembly Dimensions, in. (mm) Polyethylene Tanks Stainless Steel Tanks 7.5 L, No 7.5 L, with No Agitators With Agitators Agitators Agitators 26.4 (670) 38.6 (980) 28.2 (716) 38.2 (970) 39.9 (1013) 18.5 (470)

  • Page 70: Machine With Off-Board Tanks

    Dimensions Machine with Off-Board Tanks ti12623a ti12624a PR70 † Assembly Dimensions, in. (mm) 30 L Tank 60 L Tank No Agitators With Agitators No Agitators With Agitators 75.7 (1923) 73.9 (1877) 64.9 (1648) 84.7 (2151) 32.1 (815) 32.1 (815) 32.1 (815) 32.1 (815)

  • Page 71: Technical Data

    Technical Data Technical Data Metering Pump Effective Area ..... 80 to 960 mm (0.124 to 1.49 in. ) per side Small Air Cylinder Effective Area .

  • Page 72: Graco Ohio Standard Warranty

    With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.

This manual is also suitable for:

Pr70v

Table of Contents