Related Manuals for Maco MULTI
Summary of Contents for Maco MULTI
- Page 1 TECHNOLOGY IN MOTION ONLY FOR CERTIFIED SPECIALISTS! NOT FOR END USERS! MACO MULTI TURN-ONLY AND TURN&TILT HARDWARE Maintenance and adjustment instructions for turn-only, turn&tilt, tilt-first and tilt hardware CERTIFIED SPECIALIST...
-
Page 2: Table Of Contents
MACO MULTI Contents Safety and warning information Measures to preserve the surface finish Setting the turn-only, turn&tilt and tilt-first sash Setting the scissor stay or turn-only hinge - sash part – lift/lower Setting the scissor stay or turn-only hinge – gasket compression... -
Page 3: Safety And Warning Information
MACO MULTI Safety and maintenance information WARNING! Risk of injury due to improper maintenance operations. Improper maintenance can lead to serious personal injury or material damage. For this reason: ■ B efore starting work, ensure there is sufficient room for carrying out assembly work. ■ E nsure that the assembly site is kept clean and tidy. - Page 4 MACO MULTI NOTE W arranty claims can only be accepted if all maintenance operations have been carried out in full and according to the maintenance intervals (specified in the end user operating instructions), and this can be verified. NOTE W arranty claims can only be accepted if the unit has been installed correctly and by a certified specialist. - 4 -...
-
Page 5: Measures To Preserve The Surface Finish
MACO MULTI Measures to preserve the surface-finish Protection against soiling: ■ T he hardware should be kept free of debris and soiling. Immediately remove soiling during the building stage caused by plaster, mortar or similar with water. ■ P rotect hardware components from contamination (dust, dirt, paint, etc.). Protection against corrosion: ■ V entilate the hardware and or the rebate areas so that they are not exposed to direct moisture or condensation (important during the building stage). -
Page 6: Setting The Scissor Stay Or Turn-Only Hinge - Sash Part - Lift/Lower
MACO MULTI Adjustment values are always specified in regard to the hinge-side air gap and/or the bottom horizontal air gap. Setting scissor stay or turn-only hinge 1. Lift/lower ■ MULTI-MATIC / MULTI-TREND corner hinge version max. 1 +2,85 / -1,8 The adjusting screw must not protrude more than a maximum of 1 mm! ■... -
Page 7: Setting The Scissor Stay Or Turn-Only Hinge - Gasket Compression
MACO MULTI ■ MULTI POWER -2,5 / +1 2. Gasket compression ■ MULTI-MATIC scissor stay -1 / +1 ■ MULTI-MATIC turn-only hinge - sash part -1,5 / +1,5 - 7 -... - Page 8 MACO MULTI ■ MULTI POWER scissor stay -0,7 / +0,7 ■ MULTI POWER turn-only hinge - sash part -1 / +1 - 8 -...
-
Page 9: Pivot Post Setting
MACO MULTI Pivot post setting ■ PVC / DT / TO / AS pivot post -2,3 / +2,3 -2,3 / +2,3 -2 / +3 -1 / +1 ■ PVC / AS rebated corner support -1 / +1 -2 / +2... - Page 10 MACO MULTI ■ Drill-in pivot post -2 / +2 -2 / +2 -0,75 / +0,75 ■ MULTI MAMMUT pivot post -3 / +3 -2 / +3 - 10 -...
- Page 11 MACO MULTI ■ MULTI POWER pivot post -1 / +2 -1 / +2 -0,5 / +0,5 - 11 -...
-
Page 12: Tilt-Only Sash Setting
MACO MULTI Tilt-only sash setting ■ Side adjustment -2,5 / +2,5 ■ Lift/lower -2 / +2 ■ Gasket compression -1 / +1 - 12 -... -
Page 13: Setting The Closing Element, Setting The Sash Lifter
MACO MULTI Setting the closing element, the bullet catch and the sash lifter ■ Setting the gasket compression on the cam -0,55 / +0,55 -0,75 / +0,75 Locking cam i.S. Security roller cam ■ Setting the sash lifter -3 / +3 -3 / +3 ■... -
Page 14: Hinging And Unhinging The Sash
MACO MULTI Hinging and unhinging the sash ■ MULTI-MATIC / MULTI-TREND scissor stay hinge – PVC / DT / AS Correct position of the pin after hinging 1. Remove the cover, if there is one. 2. Pull the scissor stay-hinge pin downwards with a suitable tool. The scissor stay hinge pin can only be withdrawn when the window is closed. - Page 15 MACO MULTI ■ MULTI POWER (see also video at www.maco.eu): 1. Open the sash 90°. 2. Trigger the mishandling device (only on turn&tilt windows), turn the handle to the tilt position 3. Open the scissor stay arm safety device/turn-only hinge arm sa- fety device 4.
- Page 16 MACO MULTI Satisfied? We appreciate your feedback@maco.eu MAYER & CO BESCHLÄGE GMBH Order no. 757070EN – Date: May 2015 Date changed: October 2016 Alpenstraße 173 All rights reserved and subject to change. Graphic source: MACO, fotolia.com, A-5020 Salzburg Fachverband Schloss- und Beschlagindustrie e.V This print document is revised regularly.