Manual Tests - Maytag Bravos X Series Technician Manual

FOR SERVICE TECHNICIAN'S USE ONLY
MANUAL TEST MODE — See page 4 to access Manual Test Mode.
Pressing the START button will activate/deactivate each output. When the output is activated, the
corresponding Status LEDs will flash. IMPORTANT: Lid must be closed and locked to perform SPIN
& AGITATE tests.
OUTPUT
Output Details
NOTE: Outputs will time-out after 5 minutes.
LID LOCK
Lock and unlock the lid. NOTES: When lock is enabled, the "Lid Lock" LED will turn ON. Will only lock when lid is closed.
Will only unlock when basket RPM is 0. If lid is not closed, washer will beep and LEDs will flash.
• If lid does not lock or unlock, go to TEST #8: Lid Lock, page 18.
COLD VALVE
Turns ON and turns OFF cold water valve.
• If valve does not turn on, go to TEST #2: Valves, page 13.
HOT VALVE
Turns ON and turns OFF hot water valve.
• If valve does not turn on, go to TEST #2: Valves, page 13.
RESERVED FOR FUTURE DEVELOPMENT
If selected, washer will beep and LEDs will flash.
RESERVED FOR FUTURE DEVELOPMENT
If selected, washer will beep and LEDs will flash.
FABRIC SOFTENER DISPENSER
Turns ON and turns OFF the fabric softener valve. (May not be available on all models or brands.)
• If valve does not turn on, go to TEST #2: Valves, page 13.
OXI DISPENSER
Turns ON and turns OFF the Oxi dispenser valve. (May not be available on all models or brands.)
• If valve does not turn on, go to TEST #2: Valves, page 13.
DRAIN
Turns ON and turns OFF the drain pump.
• If pump does not turn on, go to TEST #7: Drain Pump, page 17.
RESERVED FOR FUTURE DEVELOPMENT
If selected, washer will beep and LEDs will flash.
LOW SPIN (To perform test, Lid Lock must first be enabled)
Spins basket from 0 to 500 RPM. NOTE: Allow up to 15 seconds for shifter to reposition.
IMPORTANT: To activate Low Spin, RPM must read "0" and lid must be closed with lid lock enabled.
If lid is not closed, washer will beep and LEDs will flash. IMPORTANT: Water in tub must be drained before test.
• If motor does not spin, go to TEST #3a & 3b: Drive System (Shifter & Motor), pages 13 & 14.
HIGH SPIN (To perform test, Lid Lock must first be enabled)
Spins basket from 0 to maximum RPM. NOTE: Allow up to 15 seconds for shifter to reposition.
IMPORTANT: To activate High Spin, RPM must read "0" and lid must be closed with lid lock enabled.
If lid is not closed, washer will beep and LEDs will flash. IMPORTANT: Water in tub must be drained before test.
• If motor does not spin, go to TEST #3a & 3b: Drive System (Shifter & Motor), pages 13 & 14.
GENTLE AGITATION (To perform test, Lid Lock must first be enabled)
Shifts from idle motor to gentle CW/CCW agitation. NOTE: Allow up to 15 seconds for shifter to reposition.
IMPORTANT: To activate Gentle Agitation, RPM must read "0" and lid must be closed with lid lock enabled.
If lid is not closed, washer will beep and LEDs will flash.
• If motor does not agitate, go to TEST #3a & 3b: Drive System (Shifter & Motor), pages 13 & 14.
HEAVY AGITATION (To perform test, Lid Lock must first be enabled)
Shifts from idle motor to heavy CW/CCW agitation. NOTE: Allow up to 15 seconds for shifter to reposition.
IMPORTANT: To activate Heavy Agitation, RPM must read "0" and lid must be closed with lid lock enabled.
If lid is not closed, washer will beep and LEDs will flash.
• If motor does not agitate, go to TEST #3a & 3b: Drive System (Shifter & Motor), pages 13 & 14.
DO NOT REMOVE OR DESTROY
= ON
STATUS LEDs DISPLAY
If Available
1
2
2 1
4
4 1
4 2
4 2 1
8
8 1 On
8 2 On
On
8 2 1
On
8 4
PAGE 9
00
01
02
03
04
05
06
07
08
09
10
1 1
12