Important Notes; Technical Data; Noise Emission Values; Before Putting The Machine Into Operation - EINHELL RT-SB 305 U Operating Instructions Manual

Anleitung RT-SB 305 U_SPK1:_
GB

4. Important notes

Safety information
IMPORTANT! Whenever you use electric tools it is
imperative to take basic safety precautions in order
to reduce the risk of fire, electric shock and personal
injury.
The corresponding safety information can be found
in the enclosed booklet.
CAUTION!
Read all safety regulations and instructions.
Any errors made in following the safety regulations
and instructions may result in an electric shock, fire
and/or serious injury.
Keep all safety regulations and instructions in a
safe place for future use.

5. Technical data

Voltage:
Power:
Ideal speed no:
Blade length:
Max. blade width:
Blade speed:
Cutting height:
Throat:
Table size:
Tilting range of table:
Workpiece size:
Weight:

Noise emission values

Sound pressure level L
pA
Sound power level L
WA
6. Before putting the machine into
operation
Make sure the machine stands securely, i.e. bolt
it to a workbench or solid base. There are two
holes for this purpose in the machine foot.
The saw table must be mounted correctly.
All covers and safety devices have to be properly
16
03.10.2008 9:40 Uhr Seite 16
fitted before the machine is switched on.
It must be possible for the blade to run freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
7. Assembly
CAUTION!
Pull out the power plug before carrying out any
maintenance, resetting or assembly work on the
bandsaw!
7.1 Assembly of the sub-frame and wheels (Fig.
3-5/27)
230V ~ 50 Hz
First attach the legs (21) loosely to the base
740 W
plate (5) of the machine using 2 screws for each
1400 min -1
leg. Use the round head M8x12 screws to do so.
Screw the 2 long struts (41) and the 2 short
2240 mm
struts (42) loosely to the legs (21). The doubled-
6,5 - 20 mm
over part of the struts must be at the top.
370/800 m/min
Attach rubber feet to the legs (21).
5 -170 mm / 90°
Place the machine on the legs.
Align the entire base frame and tighten all
70 mm / 45°
screws.
305 mm
Screw the wheels (10) on the rear of the
520 x 400 mm
machine to the legs (21) as shown in Fig. 4.
0° to 45°
Screw the transport handle (44) to the rear of
the machine using 2 screws (49).
600 x 600 mm
Fasten the holder (29) for the push stick (28) as
52 kg
follows: Screw the lock nut onto the bolt (29)
and then screw this into the housing until the
push stick (28) can be hung up.
Cutting
92,7 dB(A)
7.2 Assembling the saw table (Figures 6-9)
102,3 dB(A) Slacken the wing nuts (45) on the underside of
the saw table (15) and remove the chain bar (2)
from the saw table.
Lead the blade through the slot (a) in the
machine table and place the machine table on
the table guide so that the clamping screw (47)
fits through the mounting (48).
Screw the saw table tight with the wing nut (18).
Place the chain bar (2) on the saw table (15) so
that the screw heads (50) slide into the guide
slots (51).
Check that the blade (25) runs freely and does