Page 1
Anleitung_RT_TS_1825_U_SPK7:- 10.06.2010 7:10 Uhr Seite 1 ® Operating Instructions Table Saw 1825 U Art.-Nr.: 43.406.39 I.-Nr.: 11010 RT-TS...
Page 2
Anleitung_RT_TS_1825_U_SPK7:- 10.06.2010 7:10 Uhr Seite 2 Read and follow the operating instructions and safety information before using for the first time.
Page 3
Anleitung_RT_TS_1825_U_SPK7:- 10.06.2010 7:10 Uhr Seite 3...
Page 4
Anleitung_RT_TS_1825_U_SPK7:- 10.06.2010 7:10 Uhr Seite 4 3-5 mm...
Page 5
Anleitung_RT_TS_1825_U_SPK7:- 10.06.2010 7:11 Uhr Seite 5 45°...
Page 6
Anleitung_RT_TS_1825_U_SPK7:- 10.06.2010 7:11 Uhr Seite 6...
Page 7
Anleitung_RT_TS_1825_U_SPK7:- 10.06.2010 7:11 Uhr Seite 7...
Page 8
Anleitung_RT_TS_1825_U_SPK7:- 10.06.2010 7:11 Uhr Seite 8...
Anleitung_RT_TS_1825_U_SPK7:- 10.06.2010 7:11 Uhr Seite 9 3. Items supplied Important! When using the equipment, a few safety precautions Table saw must be observed to avoid injuries and damage. Carbide-tipped saw blade Please read the complete operating instructions and Parallel stop safety regulations with due care.
Anleitung_RT_TS_1825_U_SPK7:- 10.06.2010 7:11 Uhr Seite 10 design: necessarily reliable workplace values. Although there Contact with the saw blade in the uncovered is a correlation between emission and immission saw zone. levels it is impossible to draw any certain conclusions Reaching into the running saw blade (cut as to the need for additional precautions.
Page 11
Anleitung_RT_TS_1825_U_SPK7:- 10.06.2010 7:11 Uhr Seite 11 such as nails or screws etc. 7.3 Fitting / removing the saw blade guard (Fig. 3) Before you actuate the On/Off switch, make sure Mount the saw blade guard (2) on the splitter (5) that the saw blade is correctly fitted and that the so that the screw fits through the hole (44) in the machineʼs moving parts run smoothly.
Anleitung_RT_TS_1825_U_SPK7:- 10.06.2010 7:11 Uhr Seite 12 Clean the blade flange thoroughly before fitting side of the saw table (1). the new blade. The parallel stop (7) has to be mounted in the Mount and fasten the new saw blade in reverse guide rail (22) of the saw table (1).
Anleitung_RT_TS_1825_U_SPK7:- 10.06.2010 7:11 Uhr Seite 13 reach its maximum speed of rotation before Set the blade (4) to the desired angle. (See 8.5.) commencing with the cut. Set the parallel stop (7) in accordance with the Take extra care when starting the cut! workpiece width and height (see 8.3.1) Carry out the cut in accordance with the 9.1.
Page 14
Anleitung_RT_TS_1825_U_SPK7:- 10.06.2010 7:11 Uhr Seite 14 Never place any electric tools in your household refuse. Seek advice on correct disposal from local waste authorities.
Page 15
Anleitung_RT_TS_1825_U_SPK7:- 10.06.2010 7:11 Uhr Seite 15 The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of ISC GmbH. Technical changes subject to change...
The Einhell Express Guarantee is valid for a period of 2 years starting from the purchase date of the product. Claims made under the Einhell Express Guarantee should be submitted before the end of this guarantee period and within two weeks of the defect being noticed.
Need help?
Do you have a question about the RT-TS 1825 U and is the answer not in the manual?
Questions and answers