TABLE OF CONTENTS REGULATIONS AND SECURITY SAFETY INSTRUCTIONS SYSTEM DESCRIPTION MOUNTING INSTRUCTIONS DIFFUSER MOUNTIG GUIDE MOUNTING GUIDE AHDSR42W UI POWER AND CONTROL CONTROLS AND AUDIO FEATURES AHnet PROTOCOL AHlink MASTER CONFIGURATION INFORMATION ON DISPOSAL WARRANTY TERMS AND CONDITIONS...
Page 3
WELCOME Thank you for purchasing an ARTHUR HOLM product. Please, read this installation and operating instructions carefully and keep them in a safe place for future reference. We remain at your entire disposal if you have any suggestions. Henrik Holm General Manager hholm@albiral.com...
Page 4
ABOUT US The Company Arthur Holm has its origins in the Danish furniture designer Jorgen Alex Jensen, who was active during the sixties and the seventies. His design inspiration and his concept of ergonomics have been continued by his family, the design force behind Arthur Holm product range. The result of...
REGULATIONS AND SECURITY ATTENTION: Do not disassemble or modify the device in any way. This symbol warns of the presence of dangerous un-insulated voltages inside some of the components, of sufficient magnitude to expose people to risk of electronic shock. This symbol draws attention to important use and maintenance instructions in the manual that accompanies the unit.
Page 6
SAFETY INSTRUCTIONS Wiring connected to hazardous voltage requires installation by qualified personnel or the use of ready-made flexible cables. For your security, your equipment must be connected to an electrical outlet with grounding connection protection. Since the plug is used to disconnect the device, the operating electrical outlet must be in an easily accessible place.
DSP technology, the system can be controlled using the AHnet and its wireless AHlink App for control and set-up. The Arthur Holm dynamicSpeaker is designed to be hidden when not in use with a smooth magical and elegant movement done without disturbing the audience.
Page 8
SYSTEM DESCRIPTION Available Models MODEL DESCRIPTION Motorised loudspeaker furniture integration. 4" coaxial loudspeaker. Class-D 2way bi-amplified. RMS power 2 x 36.5W. 360° dispersion. Balanced analogue audio input. Adjustable gain through AHnet (RS422 AHDSR42W Protocol). Mute function through AHnet (RS422 Protocol). Cover plate made of stainless steel.
1. After unpacking the equipment and removing the safety screw for transport, install the equipment and connect to the power. 2. Then press the button to turn the DynamicSpeaker to open position. 3. Put together the diffusor matching the 4 magnets with the 4 top anchor screws.
Not complying with these directions will result in a loss of the Arthur Holm warranty. Albiral Display Solution S.L. shall not be held liable for any loss or injury...
Page 11
MOUNTING GUIDE AHDSR42W UI The DynamicSpeaker is available in a special version that is prepared to be mounted from below the table with a veneer finishing on the lid of the device to match the table. This special version is supplied without stainless steel cover plate and buttons.
Page 12
MOUNTING GUIDE AHDSR42W UI Veneer Centring and Fixation IMPORTANT: Don’t remove the Security Nylon screw until finishing the installation into the table. Use the centring jig to join the veneer in it’s correct position. The top plate is just the base where the veneer is going to be added. The base can not be necessary centred with the jig.
Page 13
MOUNTING GUIDE AHDSR42W UI Mounting table brackets View from below the table: Mount the table brackets below the table using the holes indicated on pattern hole drawing. The screws (x6) depend on the table material; the weight of the unit is up to 10Kg.
Page 14
MOUNTING GUIDE AHDSR42W UI Mounting the DynamicSpeaker brackets Mount the unit brackets on their corresponding side by screwing the screws (2+2 M6x20) into the lateral threads. Mount the vertical adjustment screws (2+2 M6x60) on to the unit bracket so that the tip of the screw is flushed with the upper side of the unit...
Page 15
MOUNTING GUIDE AHDSR42W UI Hanging the unit Mount 2+2 nuts on to both table brackets as indicated on the drawing. Slide the unit on to the table bracket nuts.
Page 16
MOUNTING GUIDE AHDSR42W UI Centring of the unit...
POWER AND CONTROL Pantone Process Black M ref. 0961E0001-00 24V.D.C Pantone 187C SERVICE Blanc LINE IN Tamaño etiqueta 75 x 30 mm. 0961E0001 / MDJ / Revisió 0 24V D.C.: Power supply input connector. Service: USB to be used only for service. Line in: Audio input.
CONTROLS AND AUDIO FEATURES Remote control 1. Touch button to open and close the unit Audio features • 4" coaxial loud speaker • Class-D 2 way bi-amplified • RMS power 2 x 36.5 W • 360° dispersion • Balanced analogue audio input. Level line +4dB •...
AHNET PROTOCOL Communications protocol COMMUNICATION RS422 CONNECTION RJ45 WIRING CAT-6 Speed and configuration BAUD RATE 38400 DATA BITS PARITY NONE STOP BITS Wiring Diagram 1. Data TX + 2. Data TX – 3. Data RX + 4. NC 5. NC 6 .Data RX –...
Page 20
AHNET PROTOCOL AHnet protocol Uses 5 bytes communication: BYTE 0 START BYTE BYTE 1 ADDRESS BYTE BYTE 2 COMMAND BYTE BYTE 3 VALUE 1 BYTE 4 VALUE 2 Commands COMMAND DESCRIPTION RESPONSE FA XX 01 01 00 OPEN FB XX 01 01 00 FA XX 01 00 00 CLOSE FB XX 01 00 00...
Page 21
AHNET PROTOCOL BITE CLOSED OPENED PROTECT NO PROTECT BUT_EN BUT_DIS To send an order to all the devices, you must use the address: F7 Hex. (Byte1) In this case, the units do not send a reply.
AHLINK AHlink is used to control and set-up the unit. Activate the AHlink function by pressing the open/close button on the cover plate during 3 seconds. Using a mobile phone, download the “EZ App Lynx” app from the App Store (IOS system) or Google Play (Android system). This App is cost free. Execute the EZ App Lynx on your mobile phone.
Page 23
AHLINK Select the "Scan for local devices" option and your AH device will appear on screen. The name of the device is "AH" + 4 character Bluetooth MAC address.
Page 24
AHLINK SERIAL Serial number of the unit Firmware version Control to open/close mechanical functions AUDIO: Mute audio control AHnetRCX: Last AHnet command received SENSOR STATUS: Sensor status information - S1, S2: Not used - S3: Open/Close sensor switch. The sensor is Off while pressing the Open/Close button on the cover plate - S4: Mechanical close sensor.
Page 25
AHLINK SERIAL Serial number of the unit OPEN: Opens the unit CLOSE: Closed the unit AUTO ADJUST: Auto adjust the speed and protection parameters SPEED OPEN FAST: Speed open fast value SPEED OPEN SLOW: Speed open slow value SPEED CLOSE FAST: Speed close fast value SPEED CLOSE SLOW: Speed close slow value PROTECTION OPEN FAST Protection open fast value...
MASTER CONFIGURATION Configuring a MASTER unit, allows to control using the AHlink application, all the units installed in the same room. When the unit is configured as MASTER, the AHlink signal is always active and you can control all the signals installed.
Page 27
MASTER CONFIGURATION Use the AHLink application to connect to the MASTER unit and control all the units connected to the MASTER as shown on previous figure. OPEN/CLOSE: Controls the open and close mechanical function in all units connected to the MASTER AUDIO ON/OFF: Controls the audio mute function in all units connected to the MASTER -/+/SAVE: Controls the volume level in all units connected to the...
INFORMATION ON DISPOSAL FOR USERS OF WASTE ELECTRICAL & ELECTRONIC EQUIPMENT This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to the designated collection points, where they will be accepted on a free of charge basis.
WARRANTY TERMS AND CONDITIONS Albiral Display Solutions warrants this product against manufacturing defects and workmanship for a period of two (2) years from the date of purchase, subject to the conditions below. Electrical, electronic boards, accessories and power supply are warranted against manufacturing defects and workmanship for a period of two (2) years from the date of purchase Labour costs: Albiral Display Solutions covers the labour costs to...