Standard Warm Up Times; In Particular - Chicco 06785 Instructions Manual

bottle support (b) before being inserted inside the main body (a).
Make sure that no water overflows from the top of the appliance; for small sized feeding bottles or
jars, check that the water does not reach the top or open mouth of the same.
If water overflows from the bottle warmer when the feeding bottle is placed inside the main body
(a), immediately use a dry cloth to dry the outside and base of the bottle warmer and the power
cord; then pour out the water in excess from the tank.
4. Connect the power cord connector (c) to the appliance and plug it into the mains socket. The
appliance will beep when it is connected correctly (1 beep).
5. Press and hold the ON/OFF button (d5) for about 3 seconds to switch the bottle warmer ON.
NB: After 3 minutes of inactivity or from the end of the "warm-up" cycle, the appliance will switch to
"stand-by" mode and the green led above the main button will blink. To restart the appliance when
it is in "stand by" mode, briefly press and release the "ON/OFF" button (d5).
NB: To switch the bottle warmer off, at any time, press and hold the "ON/OFF" button (d5).
6. Select the type/capacity of the container to be warmed by pressing the Feeding Bottle (capac-
ity)/Jar selector button selector button (d2) until the blue led is positioned on the desired option:
Jar, Feeding Bottle 150 ml; Feeding Bottle 250 ml; Feeding Bottle 330 ml.
7. Set the starting temperature of the food by pressing the food starting temperature selector but-
ton (d3) until the blue led is positioned on the desired option: Ambient temperature (* about
20°C); Average fridge temperature (** about 5°C); Average freezer temperature (*** about -18°C);
8. Press and release the "ON/OFF" button (d5) to start the selected cycle. The red led above the but-
ton will come on (fixed light) to signal the start of the warm-up cycle. The warming cycle count-
down time can be seen on the display (d1). At the end of this cycle, a visual signal will appear on
the display (d1 (00) and the ON/OFF button led will turn to green. In addition, the appliance will
beep 5 times to indicate the food is ready.
STANDARD WARM UP TIMES (in minutes)
20°C
Starting
5°C
temperature
-18°C
9. On removing the bottles and/or baby food jars from the main body of the bottle warmer (a),
dry them carefully.
WARNING
The warming cycle times in the table above refer to Chicco feeding bottles and 80 ml jars. The final
temperature may not be that desired with feeding bottles of other brands and jars of different sizes.
Before feeding your baby, always check the temperature of the contents is not too hot.
If the food is not hot enough, put it back in the warmer and repeat the warming cycle. Check the
warming status at regular intervals, taking care not to burn yourself, until the required temperature
is reached.

IN PARTICULAR:

For feeding bottles:
- Shake the feeding bottle for a few seconds to ensure the temperature of the contents is even; then
Feeding Bottle (capacity) or jar
Feeding bottle Feeding bottle
approx. approx.
150 ml/5 oz 250 ml/9 oz
3.5 min 4 min
5 min 6 min
13 min 18 min
18
Feeding bottle
approx. Baby food jar
330 ml/11 oz
5.5 min 7 min
8 min 8.5 min
24 min 19 min
ch
For
– St
to
NB
be
10.
US
Th
Fol
6. P
r
7. P
Th
wil
Th
At
led
NB
Tim
wit
you
We
NB
- W
- M
fo
CL
Wh
the
an
DE
Du
can
fro
an
Ne
On
ins
Fill
ml
bu