Advertisement
Table of Contents
Thank you for showing your confidence in us by purchasing the BEHRINGER TUBE AMP
MODELER TM300. This high-quality effects pedal provides 3 classic guitar amps, 3 gain
modes and 3 mic placements for a total of 27 configurations that let you easily achieve
the most sought-after tube amp sounds from clean, crunch to super-fat distortion.
Thanks to its high-performance features you can achieve the typical hard rock or heavy
metal distortion sounds.
The LEVEL control adjusts the output level.
The LOW control allows you to boost/cut the low-frequency range.
The HIGH control allows you to boost/cut the high-frequency range.
The DRIVE control adjusts the amount of overdrive effect.
The MIC switch simulates the microphone placement (orientation and distance) in
relation to the cabinet. Select CLSIC (Classic: distant mic placement without ambience)
to achieve high mid-range content and a greater definition of notes like with classic
early tube amps. In CNTR (Center: close miking at the center of a cone) you get
greater high mid-range content and increased low-end for mega crunchy results.
OFF X (Off Axis: close miking at the edge of a cone) is very similar to CNTR, but
produces a smoother, softer sound with less upper mid-range content; perfect in
combination with MODE position HOT.
Use the MODE switch to dial up one of 3 gain settings (HOT, HI G, CLN) that you
want to combine with the amp setting.
Use the AMP switch to select one of 3 great classic tube amps. You will recognize
these classic amp tones as soon as you hear them. For crystal-clear, transparent
sounds with dynamic bass select TWEED. For aggressive mids and incredible
sustain select BRIT(ISH). Rounder and more evened-out (yet still sophisticated)
sounds can be dialed up if you select CALIF(ORNIAN); it's perfect for leads.
The ON/BATT LED illuminates when the effect is activated. It also serves as a
battery level indicator.
Use the footswitch to activate/deactivate the effect.
Use this 1/4" TS IN connector to plug in the instrument cable.
The 1/4" TS OUT connector sends the signal to your amp.
Use the DC IN connection to plug in a 9 V power supply (not included).
The BATTERY COMPARTMENT is located underneath the pedal cover. To install or
replace the 9 V battery (not included), press the hinges with a ballpoint pen and remove
the pedal cover. Be careful not to scratch the unit.
TUBE AMP MODELER TM300
1. CONTROLS
Top view
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Behringer TM300
Summary of Contents for Behringer TM300
- Page 1 TUBE AMP MODELER TM300 Thank you for showing your confidence in us by purchasing the BEHRINGER TUBE AMP MODELER TM300. This high-quality effects pedal provides 3 classic guitar amps, 3 gain modes and 3 mic placements for a total of 27 configurations that let you easily achieve the most sought-after tube amp sounds from clean, crunch to super-fat distortion.
-
Page 2: Specifications
Technical specifications and appearance subject to change without notice. The information contained herein is correct at the time of printing. BEHRINGER accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained herein.
Need help?
Do you have a question about the TM300 and is the answer not in the manual?
Questions and answers
Здравствуйте Вам ! перестала включаться педаль, тру байпасс работает, а при нажатии включения, не включается. питание от блока питания, подключал разные.
The Behringer TM300 pedal turns on when a plug is inserted into the IN connector. If the bypass is working but the pedal is not turning on, possible reasons include:
1. Power Supply Issue – Ensure the pedal is receiving power. If using a battery, check that it is properly installed and not depleted. If using an adapter, confirm it provides 9V DC, center-negative polarity, and at least 100mA.
2. Input Jack Activation – The pedal powers on when a plug is inserted into the IN jack. If the connection is faulty or the jack is damaged, the pedal may not turn on.
3. Internal Damage or Faulty Components – If power and connections are correct, internal damage or a faulty circuit could be the issue, requiring professional repair.
Try replacing the battery or using a different power adapter, and ensure the input jack is fully inserted and functioning properly.
This answer is automatically generated