Service Mode Table; Dvd Self Diagnostic Function-Error Code - Panasonic DVD-S33EE Service Manual

DVD-S33EE / DVD-S33GC / DVD-S33GCA / DVD-S33GCS / DVD-S33GCU / DVD-S33GN
9.2.

Service Mode Table 1

The service modes can be activated by pressing various button combination on the player and remote control unit. please carry out
your operation based on the remote control supplied with Panasonic DVD player of previous models.
Player buttons Remote control unit buttons
PLAY
+
OPEN/CLOSE
STOP+PLAY
9.3.

DVD Self Diagnostic Function-Error Code

Error Code Error Content
U11 Focus error
H01 Tray loading error
H02 Spindle servo error
H03 Traverse servo error
H04 Tracking servo error
H05 Seek error
H07 Spindle motor drive
error
F893 FROM falsification
F894 EEPROM falsification
F895 Language area
abnormality
F897 initialize is not
completed
F740 When HDMI device key
writing failes
F750 When the HDMI Device
Key was wrong
Note:
An error code will be canceled if a power supply is turned OFF.
*1: When FROM or Module P.C.B. is replaced, be sure to write the present value into the player as the initial setting of laser
drive current. (Refer to section 9.5 initial setting of laser drive current.)
Writing method: Press the "PAUSE" button on the remote control unit while pressing the "PLAY" and "OPEN/CLOSE" buttons
on the player.
0 Displaying the UHF display F_ _ _
5 Jitter check, tilt adjustment
*Display shows J_xxx/yyy_zz
"yyy" and "zz" shown to the right have nothing to do with the jitter
value. "yyy" is the error counter, while "zz" is the focus drive
value.
6 Checking the region numbers and broadcast system
7 Checking the program version
9 Lighting Confirmation Function of Display Tube
FUNCTIONS Checking the laser drive current
PAUSE Writing the laser drive current value after replacing the optical
pickup (do not use for anything other than optical pickup
replacement)
POWER Initializing the DVD player
(restoring factory preset settings)
Additional error explanation
Focus coil, FE singal error
LD motor error, DV5.0 (IC8001) error
(Spindle servo, DV5.0 (IC8001) SP motor,
CLV servo error)
Traverse servo, DV5.0 (IC8001) , TRV motor
error
Tracking coil, DV5.0 (IC8001) error
TRV Motor, IC8251 error
SP motor current error, IC8251 error
Firmware soft error, DV5.0 (IC8001) error
Firm version agreement check for factory
preset setting failure prevention
Initialize completion check for factory preset
setting failure prevention
2
I C error occurred while writing to Device Key
in Tx.
When the HDMI Device Key was wrong
Application
Defect 1
TRV Unit DV5.0 (IC8001)
LD Motor IC8251
LD Motor DV5.0 (IC8001)
TRV Motor DV5.0 (IC8001)
TRV Unit DV5.0 (IC8001)
TRV Motor IC8251
TRV Unit IC8251
FROM DV5.0 (IC8001)
(*1)
(IC8651)
EEPROM Serial communication
(IC6201) on line
FROM
(*1)
(IC8651)
22
Note
Refer to section 9.3. Self-
Diagnosis Function (UHF
Display).
Check the IC8651 FLASH
ROM program.
Refer to section 9.1.
Optical Pickup
Replacement Procedure.
Refer to section 9.5.
Initializing the DVD
player.
Defect 2 Defect 3 Defect 4