Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Baumatic BT06.7ME
Summary of Contents for Baumatic BT06.7ME
- Page 1 BT06.7ME/BT08.7ME 60 cm Integrated hood I Bit waeady...
- Page 2 User Manual for your Baumatic BT06.7ME/BT08.7ME 60 cm Integrated hood NOTE : This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
-
Page 3: Table Of Contents
Specifications of your cooker hood Using your Baumatic cooker hood Cleaning your Baumatic cooker hood The grease filter Maintenance Removing and cleaning the grease filter (BT06.7ME) Removing and cleaning the grease filters (BT08.7ME) Changing a light bulb Fitting the carbon filters Installation... -
Page 4: Environmental Note
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. -
Page 5: Important Safety Information
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Technical Department. - Page 6 you handle your appliance, especially during installation and cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTER! o If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type.
- Page 7 removing air from your room. Ensure that proper ventilation measures are being observed. o Note that the cooker hood removes odours from your kitchen, not steam. o Warning - Always ensure that the cooker hood has been disconnected from the power supply before carrying out any work on the hood, including cleaning and replacing light bulbs.
-
Page 8: Specifications Of Your Cooker Hood
1 light o 2 lights o Aluminium filter included o Extraction capacity: o Noise level min/max: 48 – 61 dB(BT06.7ME) Optional Extra: 1 x CFM1 carbon filter for air recirculation mode (BT06.7ME) 2 x CFM1 carbon filters for air recirculation mode (BT08.7ME) - Page 9 Make sure that it has been installed by a suitably qualified person, as per the information contained in Baumatic’s installation instructions. o Find the control panel, which can be located by opening the front panel and looking on the right hand side of the cooker hood.
-
Page 10: Cleaning Your Baumatic Cooker Hood
OR AT THE VERY LEAST WHEN YOU BEGIN COOKING. YOU SHOULD ALSO RUN YOUR HOOD FOR TEN MINUTES AFTER YOU HAVE FINISHED COOKING. Cleaning your Baumatic cooker hood IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE SWITCHED YOUR COOKER HOOD OFF AT THE OMNI-POLAR SWITCH, SET AT THE WALL FROM THE CABLE. -
Page 11: Maintenance
Maintenance Removing and cleaning the grease filter (BT06.7ME) o Soak the grease filter in hot water and washing up liquid for about an hour. o Rinse it off thoroughly with hot water. o Repeat the process if required. o Refit the grease filter once it has dried. -
Page 12: Removing And Cleaning The Grease Filters (Bt08.7Me)
o Soak the grease filters in hot water and washing up liquid for about an hour. o Rinse them off thoroughly with hot water. o Repeat the process if required. o Open the front cover. Remove the grease filters by pulling down on their handles, and then pulling them upwards away from... -
Page 13: Changing A Light Bulb
IMPORTANT: BEFORE ATTEMPTING TO CHANGE A LIGHT BULB, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY. o Open the front cover and remove the grease filter (as described on page 11 or 12). o Prior to touching the light bulbs ensure that they have cooled down. - Page 14 on page 11 or 12). o If you are replacing the existing carbon filter, then you need to remove it by twisting it anti-clockwise. o (BT08.7ME only) Repeat this process for the second carbon filter. You need to place a carbon filter over both motors. o Refit the grease filter and close the front screen.
-
Page 15: Installation
Installation IMPORTANT: Before installation and usage read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the rating plate are exactly the same as the voltage and frequency in your home. The rating plate can be found behind the grease filter. -
Page 16: Before Beginning Installation
correspond with the coloured markings identifying the terminals in your spur box, please proceed as follows: o The blue wire must be connected to the o The brown wire must be connected to the Before beginning installation o Check that the product purchased is of a suitable size for the chosen installation area. -
Page 17: Installing Your Cooker Hood
IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE INSTALLING YOUR COOKER HOOD WHETHER TO USE IT IN EXTRACTION MODE OR RECIRCULATION MODE. PLEASE TURN TO PAGES 21-22 NOW TO UNDERSTAND THE DIFFERENCES BETWEEN THESE TWO MODES. o We recommend that at least two people install this hood. o Your cooker hood should only be fitted to a wall and secured between two cupboards. - Page 18 2. Whilst the front panel is still open, remove the two screws (B). Press the tab (C) down and remove the front panel from its guide rails. 3. Secure the extractor mounting brackets (D) onto the top of the hood, using the screws and washers (E) supplied. Check that the adjustment screw (F) is fitted.
- Page 19 4. Measure a distance of 1050 mm between the highest point on the hob top and the wall that you will be fixing the hood to. You should also measure and record the distance between the top of the extractor mounting brackets (D). o Using a pencil, mark this height and then attach the two mounting brackets (G) to the wall at this height, using the screws provided.
- Page 20 rear wall. There is a spacer provided that can be cut to the size of the gap and attached to the rear of the cooker hood. 7. IMPORTANT: The cooker hood must now be fixed to the adjacent cabinets, using the screws provided. You should screw through the holes in the side of the hood, into the adjacent cabinets.
-
Page 21: Connecting To External Ducting
o Connect the coupling to the top or the rear of the cooker hood, and then connect a 125 mm ducting hose to the coupling (please note that the ducting hose is not supplied with the appliance). o You may find an anti-draft flap included with the fixtures and fittings for the cooker hood. -
Page 22: Extraction Mode Or Recirculation Mode
The only alternative is to recirculate the air. Do I need a charcoal filter? All cooker hoods have a grease filter but if you are using your cooker hood in recirculation mode, then charcoal filters must be fitted in addition to the grease filter. -
Page 23: Troubleshooting
Troubleshooting IMPORTANT: If your cooker hood appears not to be operating properly, before contacting the Baumatic Service Department, please refer to the checklist below. My cooker hood will not start. o Check that the hood is connected to the electricity supply o Check that the fan speed control is set correctly. - Page 24 Or any installation other than the one specified by Baumatic Ltd. has been completed. Please refer to the conditions of guarantee that appear on the...
-
Page 25: Contact Details
Technical Advice Telephone (0118) 933 6933 E-mail: sales@baumatic.co.uk technical@baumatic.co.uk Website: www.baumatic.co.uk Republic of Ireland 01- 6266 798 Czech Republic Baumatic CR SPOL. S.R.O. 46215, Librec The Czech Republic +4204 8357 7200 www.baumatic.cz Germany Baumatic GMBH Janderstrasse 9 Mannheim, 68199 Germany +4962 112 9190 www.baumatic.de... - Page 28 28 28...
Need help?
Do you have a question about the BT06.7ME and is the answer not in the manual?
Questions and answers