Table of Contents
Advertisement
NOTE: The Blaster Soft come factory set, only to be changed by trained/qualified technicians. Changes may be
necessary should the water quality change.
First Stage of Settings
Instructions
1.
Set time clock
2.
Press NEXT and DOWN
(or Minus Button) together
3.
Press NEXT and DOWN
together a second time
4.
Press NEXT
5.
Press NEXT
6.
Press NEXT
7.
Press NEXT
8.
Press NEXT
9.
Press NEXT
10. Press NEXT
11. Press NEXT
12. Press NEXT
Second Stage of Settings
Instructions
1.
Press NEXT and DOWN
(or minus button) together
2.
Press NEXT
3.
Press NEXT
4.
Press NEXT
5.
Press NEXT
6.
Press NEXT
7.
Press NEXT
8.
Press NEXT
9.
Press NEXT
10. Press NEXT
11. Press NEXT
12. Press NEXT
13. Press NEXT
14. Press NEXT
•
NOW ADJUST REGENS... EXAMPLE BAD WATER 10 Minute backwash (our example) and 60 minutes
brine... now you may want it to go off every day...or every second day.... So follow this instruction
•
Press...Next and PLUS (+)... at the same time. "hardness "NA" will flash
•
Press... NEXT...."regen" day will flash.... Press the plus (+) or minus (-) for the day to regen... if bad water
set it at 1... this means every day it will go off.
•
Press, NEXT... back to clock setting.
NOTE: Your Blaster ozone draw time setting does not work on cycles, it works on time. This bases of design is
simple, however do not set the relay too soon, it is better to be 2 to 3 minutes longer than actual cycles add up to. If
you make it too short and the valve is in rinse the ozone will come on but won't shut off when brine draw starts.
Lastly, when the unit has finished all the cycles and goes back to service mode the ozone will automatically shut off.
BLASTER SOFT SET UP
Description
As per normal operation
Board will go to the next setting
Screen will flash this is the correct setting
ALR will flash... press plus or minus button until it says OFF
dp will flash... press plus or minus button until it says OFF
Should read "Fill"... press plus or minus button until fill is displayed on the screen
Should read "Backwash"... press plus or minus button until backwash is displayed on screen
Should read "Brine Down"... press plus or minus button until Brine Down is displayed on
screen
Should read "Rinse"... (this is just before ozone draw)press plus or minus button until Rinse
is displayed on screen
Should read "Brine Down"... press plus or minus button until Brine Down is displayed on
screen
Should read "End"... press Next until End is displayed on screen
Screen will go back to clock setting
Description
Should flash "Filtering or Softening"... press plus or minus button until Softening is displayed
on screen
Should flash " Fill"...Set at 9.5 lbs (or higher if iron count is high)
Should flash "Backwash" ... Set between 8 and 12 minutes
Should flash "Brine Draw Down"... Set for 60 minutes
Should flash "Rinse"... Set for 4 to 6 minutes
Should flash "Brine Down"... Set for 30 up to 60 minutes
Should flash "Capacity"... (unit size) usually set for 30,000 grains
Should flash "Auto"... press plus or minus buttons until Auto is displayed on screen
Should flash "Normal"... press plus or minus buttons until Normal is displayed on screen
Should flash "Relay" ... Set for "ON" (NOTE: This can be set in time or gallons, set for time)
Screen Should flash... Set the time you want the ozone to come on, you this by adding all
the cycles together. Add fill time, backwash time, brine draw time, and rinse time. You may
need to put the unit through a manual regeneration to see each time, write them down and
add them up. For example if you have 84 minutes in time before your ozone brine draw set it
for 2 more minutes = 86 minutes
Screen should flash... Set length of Ozone between 30 to 60 minutes
Should flash "Call"...leave OFF
Screen will go back to clock setting
10
Advertisement
Table of Contents
