For future reference please record the following information which be found on the Rating Plate and the date of purchase which can be found in the invoice: Model Number ……………………. Serial Number……………………. Date of Purchase…………………….
General Information Warning and Safety Instructions Instructions for Use Instructions for Installation Technical Data Conditions of Guarantee CONTENTS pages 3-4 pages 5-6 pages 7-12 pages 13-21 page 22 pages 23-24...
Installation Instructions. The use for any other purpose or in any other environment without the express agreement of Baumatic Ltd, would invalidate any warranty or liability claim Your new appliance is guaranteed against electrical or mechanical defects subject to certain exclusions noted in Baumatic Ltd Conditions of Guarantee.
Page 8
EMC – 89/336 Safety Standards – EN 60 335-1, EN 60 335 – 2 – 6, EN 30-1-1. As Baumatic have a policy of continued product improvement, the right is reserved to adjust and make any modifications deemed necessary without notification.
Baumatic therefore strongly advise that babies and young children are prevented from being near or touching the appliance at any time.
Page 10
For gas installations, the Installer must be Corgi registered (all Baumatic Engineers are Corgi registered) and for electrical installations, NICEIC registration is recommended. Baumatic Ltd declines any responsibility for injury or damage to persons or property as a result of improper use or installation of this appliance.
These User Instructions should be retained for future reference and for use by a person who is unfamiliar with the appliance. The following models are covered by these instructions: B602; B604; B609; USING THE OVEN The oven temperature is controlled by the combined thermostat and selector switch between MIN and 230°C.
If the cooling fan fails to start or operate during cooking, turn the Thermostat Selector back to the OFF position and call Baumatic Service. Do not use the appliance without the cooling fan in operation. When arranging the oven shelves,...
Page 13
If the cooling fan fails to start or operate during cooking or grilling, turn the Thermostat Selector back to the OFF position and call Baumatic Service. appliance without the cooling fan in operation. NOTE: Care should be taken when removing the heat shield as...
Page 14
USING THE 60 MINUTE MINDER (B602, B604) This run-back timer can be used independently of an oven cooking cycle for up to 60 minutes of timing. To set the timer turn the knob fully clockwise until it stops and then back to the required time.
Page 15
USING THE ELECTRONIC CLOCK (B609) The electronic clock has a display showing the hours and minutes. When the oven is switched on for the first time or immediately after a blackout, three zeros will flash on the display. To select the time, press button A and simultaneously button B or C until the current time is shown on the display.
CLEANING THE APPLIANCE Always allow the appliance to cool down to avoid a burn injury. Do not use caustic or abrasive agents, coarse wire wool or hard tools as these can damage the surface finish. Normally, wiping with a soft cloth dampened with hot detergent is sufficient but for stubborn marks the following is recommended: VITREOUS ENAMEL PARTS: Use only a cleaner that is recommended for this type of material: avoid chloride-based...
: UK law stipulates that gas appliances must be installed and NOTE repaired by a CORGI. Registered Installer (all Baumatic Engineers are CORGI Registered). Gas Safety Regulations (Installation & Use)
PRE-COMMISIONING THE APPLIANCE • When unpacked, check that the following parts are included with the appliance: • Baumatic Instruction and Installation book. • Two side-protection strips • Two oven-shelves (one with heat deflector) • Grill Pan, handle and Trivet •...
Page 19
5. A 5mm ventilation gap must be allowed between the top of the appliance and the underside of the working top. 6. If the oven is fitted into a tall housing, a 400mm² (20 x 20cm) cut-out must be provided in the support shelf and 500 x 15mm cut outs in the housing’s plinth, shelves and top.
Page 20
Fitting the Side Protection Rails Ventilation requirements when fitted into a standard base unit...
Page 21
VENTILATION OF ROOMS The actual ventilation requirements must be determined by reference to the Statutory regulations in force. GAS CONNECTION – See Page 19 (Fig. 1 to 6). The gas supply must be connected by use of the ½ BSP Adapter and an approved flexible Plug-in hose (Fig 1).
Page 22
Grill Burner • Remove the grill burner. (Fig. 5) • Replace the injector with the one suitable for the gas to be used as listed in the Technical Data. It is recommended that the appropriate thread sealant is used, always check for gas soundness after assembly.
Page 23
Fig 1 Fitting the ½ BSP Adapter and sealing washer Fig 2 Removing rear wall assembly Fig 5 Removing Grill-burner assembly. Fig 7 To be used as an extension of the appliance gas ramp to enable easy fitting and correct positioning of the flexi gas hose.
ELECTRICAL CONNECTION Before connecting the appliance, ensure that the supply voltage marked on the Rating Plate corresponds with the mains supply voltage. WARNING – THIS APPLIANCE MUST BE EARTHED This appliance should be wired into a 13Amp double pole switched fused spur outlet having 3mm contact separation and the fuse rating reduced to 3Amps, and placed in an easily accessible position adjacent to the appliance.
Before carrying out any maintenance, disconnect the appliance from the electricity supply. During the guarantee period, in case of need all service interventions should be referred back to the Baumatic Ltd Service department. Please note that intervention or repair by any unauthorised personnel will invalidate such guarantee.
TECHNICAL DATA DIMENSIONS Height Width Depth ELECTRICAL DETAILS Rated Voltage: Supply Connection: 3mm contact gap) Power Input: Mains Supply Lead: 3 x 1.0mm² Type H05 RR-F <HAR> Oven Light Bulb GAS DETAILS Connection: Rp ½ (1/2 BSP male thread) Type: Natural Gas G 20 (20.9mbar) –...
All ‘Work’ in relation to the Guarantee must be carried out by Baumatic Ltd or an approved service agent of Baumatic Ltd. Any claims made under the terms of the guarantee must be supported by the original invoice / bill of sale issued at the time of purchase.
Page 28
For ROI (Republic of Ireland), please contact one of the numbers as below: Tel: 01 – 4030501 FAX: 01 – 4030503 Thank you for buying Baumatic. SERVICE TEL 0118 933 6911 FAX 0118 986 9124 SPARES TEL 0118 933 6922...