Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for FUXTEC FX-AF1139
Summary of Contents for FUXTEC FX-AF1139
- Page 1 Original User Manual FX-AF1139_rev03...
-
Page 2: Table Of Contents
Original User Manual FX-AF1139_rev03 7.2. WORKING WITH THE MILLING DEVICE 7.2.1. SUGGESTED USE INDEX MAINTENANCE INTRODUCTION 8.1. MAINTENANCE AND CARE AFTER USE SAFETY PRECAUTIONS 8.1.1. GENERAL CHECKPOINTS 8.1.2. CLEANING 2.2. PERSONAL SAFETY 8.1.3. CHECKING THE OIL LEVEL 2.2.1. WORK CLOTHING 8.2. -
Page 3: Introduction
Original Bedienungsanleitung FX-AF1139_rev03 INTRODUCTION Attention! Read all safety instructions and all instructions. Failure to observe all warnings and instructions below may result in fire and severe injury. Before using this device, carefully read this manual's information regarding proper setup and safety precautions. -
Page 4: Safety Precautions
Original User Manual FX-AF1139_rev03 Avoid inhaling the exhaust fumes. This device produces SAFETY PRECAUTIONS dangerous gases such as carbon monoxide, which can cause dizziness, fainting, or death. To avoid operating errors of this device, please read Do not use this device if you are tired or under the all instructions in this manual before the first use. -
Page 5: Work Clothing
Original Bedienungsanleitung FX-AF1139_rev03 leave the device alone, switch off the engine, wait until High vibrations and long exposure times contribute to the cutting tool stops, and remove the plug from the white finger disease. To reduce the risk, it is necessary spark plug. -
Page 6: Safe Handling Of Fuels
Original User Manual FX-AF1139_rev03 Keep the working area clean and work with good lighting. Only use this device in daylight or with Do not refuel in enclosed spaces, in poorly adequate artificial lighting. Unclear and dark areas ventilated areas, or near flames. cause accidents. -
Page 7: Maintenance
Original Bedienungsanleitung FX-AF1139_rev03 Before working with the device, make sure that the cutting tools have no contact with objects and can move freely. Do not use the device on steep slopes where your safety is not guaranteed. When working on a hill, slow down your working speed and ensure good stability. -
Page 8: Warning Symbols
Original User Manual FX-AF1139_rev03 WARNING SYMBOLS Dispose of your device in an environmentally friendly manner. Do not Warning symbols indicate the information required for merely throw it into a trash can the use of the device. Complies with CE guidelines (EU Warning: Danger! standards) Read this manual carefully before... -
Page 9: Device Description
Original Bedienungsanleitung FX-AF1139_rev03 5. DEVICE DESCRIPTION 5.1. TERMS OF USE Use this device only to order the country. Do not use this device for purposes other than those for which it was designed. The use of this device for other than the intended work can lead to dangerous situations. Remember that the device operator is responsible for any hazards and accidents caused to other people or things. -
Page 10: Technical Features
Original User Manual FX-AF1139_rev03 5.3. TECHNICAL FEATURES Description Tiller Brand FUXTEC FX-AF1139 Model Engine 4-stroke engine Displacement (cm³) Maximum power (kW) / revolutions (min-¹) (ISO 8893) 2.2 / 3000 Fuel consumption at maximum output (kg/h) 0.97 Number of milling tools... -
Page 11: Start-Up
Original Bedienungsanleitung FX-AF1139_rev03 Using the device without all parts or with defective parts 6. START-UP can cause serious injury. 6.2. ASSEMBLY 6.1. UNPACKING AND LISTING OF MATERIALS 6.2.1. MOUNTING OF THE SPUR This device contains the following elements, which Insert the spur (H) (as shown in the illustration) so you will find in the box: that it remains at the desired height, and insert the pin (T5) that secures it with the retaining ring (T4). -
Page 12: Handlebar Mounting
Original User Manual FX-AF1139_rev03 There are two adjustment 6.3. FUEL AND OIL heights of the transport IMPORTANT: The fuel used for this device is wheel. When transporting highly flammable. If the fuel or device ignites, or storing the milling cutter extinguish the fire with a powder fire extinguisher. -
Page 13: Engine Oil
Original Bedienungsanleitung FX-AF1139_rev03 Do not use fuels such as ethanol or methanol. These Check: fuels will damage the engine of the device. the device complete and check for loose and damaged parts (screws, nuts, etc.). 6.3.2. ENGINE OIL that the moving parts of the device have no For transport reasons, your device's engine comes from contact with any object. -
Page 14: Control Points After Starting The Engine
Original User Manual FX-AF1139_rev03 6.4.2.2. STARTING WITH A HOT ENGINE switch to the "STOP" position. Do not use this device if you are tired, sick, on drugs, Place the device on a level and stable surface to start it. narcotized, or addicted to alcohol. Lack of rest and fatigue can cause accidents or damage. -
Page 15: Working With The Milling Device
Original Bedienungsanleitung FX-AF1139_rev03 Do not use this router with one hand. Attention! MAINTENANCE Attention! This router can jump up or jump forward Perform regular inspections of the device to ensure unexpectedly. Suppose the teeth hit something hard efficient operation of the device. We recommend that buried in the ground, such as large stones, roots, or you take the device to your service technician for trunks, if the ground is too hard or if the ground is... -
Page 16: Checking The Oil Level
Original User Manual FX-AF1139_rev03 Unscrew the plug and check the mark left by the oil on device. the dipstick. The mark left by the oil must be between the minimum and maximum mark. Clean the milling area: If the mark is below the minimum, add a little more oil Switch off the engine and let it cool down. -
Page 17: Air Filter
Clean and check the spark plug regularly. plug (Y2) at the bottom of the filling nozzle or by using a FUXTEC suction pump (not included) and sucking the Check whether the electrode gap is correct (0.6 - 0.7 oil through the filling nozzle (Y1) of the device. We mm). -
Page 18: Troubleshooting
Original User Manual FX-AF1139_rev03 TROUBLESHOOTING If the device does not start, check the engine's compression and the spark of the spark plug. Depending on the symptoms you notice, you can determine the probable cause and solve it. The spark Probable cause Corrective actions compression plug is ok... - Page 19 The cutters do not break Cutter placed incorrectly, and the edges Send your device to the service department into the ground are set in the wrong direction In case you cannot solve the problem, please contact the FUXTEC customer service.
-
Page 20: Transport
Original User Manual FX-AF1139_rev03 10. TRANSPORT Never lift or transport the milling device while the engine is running. When transporting the device between different working areas, always switch off the engine. Wait 5 minutes after switching off the device to cool down before transporting. The exhaust pipe of the device remains hot after switching off the engine. -
Page 21: Declaration Of Conformity
Tested according to: EN ISO 12100-1:2003+A1:2009 EN ISO 12100-2:2003+A1:2009 EN ISO 14121-1:2007 EN 60204-1:2006+A1:2009 Herrenberg, January 8, 2020 Tim Gumprecht (Managing Director) Storage of the technical documentation: FUXTEC GmbH ● Kappstraße 69 ● 71083 Herrenberg ● Germany Tim Gumprecht, management... - Page 22 Original User Manual FX-AF1139_rev03...
Need help?
Do you have a question about the FX-AF1139 and is the answer not in the manual?
Questions and answers