Advertisement
Lutron Technical Support Center 1.800.523.9566 24 hrs / 7 days
Continued from front
5a – Single-Location Control
Brass screw
Atenuador
Dimmer
Brass
Blue
Live
Black
120 V~
Green
60 Hz
Ground
Wallbox
Black screw
Ground
Single Location Wiring Diagram
Green wire
Wiring the Dimmer:
•
Connect the
green ground wire on the Dimmer to the bare copper or green ground wire in the
wallbox. (See Important Note 2 on other side.)
•
Connect either of the wires removed from the switch to the
black screw terminal on the Dimmer.
•
Connect the remaining wire removed from the switch to the
brass screw terminal on the Dimmer.
•
Tighten the
blue screw terminal on the Dimmer. It is not used in a single-pole circuit.
5b – Two-Location Control
One location will be replaced with a Dimmer and the other with a Companion Dimmer.
Brass screw
Dimmer or
Blue screw
Companion Dimmer
Brass
Blue
Tag
Live
Black
120 V~
Green
60 Hz
Black screw
Ground
Green wire
Wallbox
Ground
Two Location Wiring Diagram
Wiring the Dimmer:
•
Connect the
green ground wire on the Dimmer to the bare copper or green ground wire in the wallbox.
(See Important Note 2 on other side.)
•
Connect the tagged wire removed from the switch in step 3b to the
•
Connect one of the remaining wires removed from the switch to the
•
Connect the remaining wire removed from the switch (note wire color) to the
the Dimmer.
Wiring the Companion Dimmer (MA-R):
Blue screw
•
Connect the
green ground wire on the Companion Dimmer to the
Brass screw
bare copper or green ground wire in the wallbox.
(See Important Note 2 on other side.)
•
Connect the wire tagged in step 3b to the
Tag
the Dimmer or Companion Dimmer.
•
Connect the same color wire connected to the
on the Dimmer (wire color noted above) to the blue screw terminal on
the Companion Dimmer.
Green wire
Ground
•
Connect the remaining wire removed from the switch to the
Black screw
screw terminal on the Companion Dimmer.
5c – Three or More-Location Control
One location will be replaced with a Dimmer and the others with Companion Dimmers. Only one Dimmer can
be used with up to nine Companion Dimmers.
Tags
Dimmer or
Dimmer or
Blue
Brass screw
Companion Dimmer
Companion Dimmer
screw
Brass
Blue
Brass
Black
Live
Black
120 V~
Green
Green
60 Hz
Wallbox
Wallbox
Black screw
Ground
Ground
Ground
Three or More Location Wiring Diagram
Green wire
Dimmer or Companion Dimmer
Replace the 4-way Switch(es):
Note: 4-way switches may be replaced with either a Dimmer or an Companion Dimmer.
•
Connect the
green ground wire on the Dimmer or Companion Dimmer to the bare copper or green
ground wire in the wallbox. (See Important Note 2 on other side.)
•
Connect both of the wires tagged in step 3c wires (noting their color) to the
the Dimmer or Companion Dimmer (one wire to the screw and the other to the push-in terminal).
•
Connect one of the remaining wires removed from the switch to the
Dimmer or Companion Dimmer.
•
Connect the remaining wire removed from the switch to the
brass screw terminal on the Dimmer or
Companion Dimmer.
Replace the 3-way switches:
Brass
screw
green ground wire on the Dimmer or Companion
Blue screw
•
Connect the
Dimmer to the bare copper or green ground wire in the wallbox.
(See Important Note 2 on other side.)
•
Connect the wire tagged in step 3b to the
Tag
the Dimmer or Companion Dimmer.
•
Connect the same color wire connected to the
on the Dimmer or Companion Dimmer that replaced a 4-way switch
Ground
Black screw
(wire color noted above) to the blue screw terminal on the Dimmer or
Green wire
Companion Dimmer.
Dimmer or Companion Dimmer
•
Connect the remaining wire removed from the switch to the
screw terminal on the Dimmer or Companion Dimmer.
6
Mounting Switches to Wallbox
Form wires carefully into the wallbox, mount and align
Dimmer (and Companion Dimmers).
Attach Claro or Satin Colors® Wallplate(s) (Sold separately).
7
Light
Turning Power ON
Fixture
Turn power ON at circuit breaker
(or replace fuse).
Neurtral
Replacing the Battery in a Wireless Controller
1
Remove the battery cover screw, then
gently slide the battery holder out of the
back of the Wireless Controller.
Using the Wireless Controller on a
Dimmer or
Car Visor
Companion Dimmer
1
Slide the metal Visor clip into the Visor
Backplate.
Blue
Brass
Light
Black
Fixture
Green
Ground
2
Wallbox
Neutral
Slide the Visor Backplate into the back of
the Wireless Controller.
black screw terminal on the Dimmer.
brass screw terminal on the Dimmer.
blue screw terminal on
3
Mount the Wireless Controller to a
vehicle's visor.
black screw terminal on
Mounting a Wireless Controller Directly to a Wall Without
blue screw terminal
a Wallplate
1
Carefully cut out the Template below along the outer dashed line and temporarily attach it to the
brass
wall at the desired mounting location.
Note: To match location of existing wall controls, remove existing wallplate and measure height
of top screw.
2
Mark and drill the two 3⁄16 in (35 mm) screw hole locations indicated within the Wall Mount
Backplate section (A) of the template.
3
Dimmer or
Insert a Screw Anchor into each of the holes drilled in step 2, making sure they are
Companion Dimmer
flush with the wall.
Note: Template should be removed from wall before inserting anchors.
Blue
Brass
Blue
4
Loosely mount the Wall Mount Backplate to the wall with screws. Check to
Light
make sure the Backplate is level. Once level, tighten the screws fully.
Black
Fixture
Green
5
Slide Wireless Controller down onto the Wall Mount Backplate. (Figure 3)
Wallbox
Ground
Neutral
Mounting a Wireless Controller in a 1-Gang Wallplate
1
Carefully cut out the Template below along the outer dashed line and temporarily attach it to the
blue screw terminal on
wall at the desired mounting location.
Note: To match location of existing wall controls, remove existing wallplate and measure height of
top screw.
black screw terminal on the
2
Mark and drill the four
3
Insert a Screw Anchor into each of the holes drilled in step 2, making sure they are flush with the wall.
Note: Template should be removed from wall before inserting anchors.
4
black screw terminal on
Loosely mount the Wall Mount Backplate to the wall with screws. Check to make sure the Backplate
is level. Once level, tighten the screws fully.
blue screw terminal
5
Slide Wireless Controller down onto the Wall Mount Backplate. (Figure 3)
brass
6
Mount the 1-gang wallplate with screws provided. Wallplate must be mounted after the Wireless
Controller is installed, not before.
Start
screws.
2
Remove the existing battery and replace with
a new CR 2032. The positive (+) side should
be down. Slide battery holder back into the
Wireless Controller unit until it snaps into
place. Replace screw.
Using the Wireless Controller as a
Handheld Remote
Slide the Blank Backplate into the back of
the Controller.
Using the Wireless Controller as a
Tabletop Remote
Slide the Wireless Controller onto the Tabletop
Pedestal. (L-PED 1 Sold separately)
Note: The visor clip
may need to be manually
opened depending on
visor thickness.
⁄
3
in (35 mm) screw hole locations indicated on the Template.
16
Template: For Mounting Directly to a Wall or
Align
in a 1-Gang Wallplate
Dimmers
and tighten
screws.
For all other configurations please visit www.lutron.com/maestrowireless
Using the Wireless Controller on a Wall
The Wireless Controller can also be mounted to the left or right of existing lighting controls,outlets or
other Wireless Controllers. For these configurations please visit www.lutron.com/maestrowireless.
Light
Light
Light
On
On
Adjust
Adjust
On
Adjust
Off
Off
LUTRON
LUTRON
Technical Assistance
Off
For questions concerning the installation or
LUTRON
operation of this product,
call the Lutron Technical Support Center.
Please provide exact model number when calling.
Figure 3
U.S.A. and Canaday (24 hrs / 7 days)
1.800.523.9466
Fax +1.610.282.6311
México +1.888.235.2910
Other Countries 8am – 8pm ET
+1.610.282.3800
www.lutron.com
Limited Warranty
(Valid only in U.S.A., Canada, Puerto Rico, and the Caribbean.)
Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after purchase. For warranty
service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid.
This warranTy is in liEu of all oThEr ExprEss warranTiEs, and ThE impliEd warranTy of mErchanTabiliTy is limiTEd
To onE yEar from purchasE. This warranTy doEs noT covEr ThE cosT of insTallaTion, rEmoval or rEinsTallaTion,
or damagE rEsulTing from misusE, abusE, or damagE from impropEr wiring or insTallaTion. This warranTy doEs
noT covEr incidEnTal or consEquEnTial damagEs. luTron's liabiliTy on any claim for damagEs arising ouT of or in
con nEc Tion wiTh ThE manufacTurE, salE, insTallaTion, dElivEry, or usE of ThE uniT shall nEvEr ExcEEd ThE pur chasE
pricE of ThE uniT.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the
exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty may last, so the above limitations
may not apply to you.
This product is covered under one or more of the following U.S. patents: 5,248,919; 5,399,940; 5,637,930; 5,798,581; 6,169,377; 6,380,696;
7,362,285; 7,365,282; 7,408,525; 7,548,216; 7,573,436 and corresponding foreign patents. U.S. and foreign patents pending. Lutron, Claro,
Maestro, Maestro Wireless, The Sunburst Logo and Satin Colors are registered trademarks and FASS is a trademark of Lutron Electronics Co.,
Inc. NEC is a registered trademark of National Fire Protection Association, Quincy, Massachusetts. © 2009 Lutron Electronics Co., Inc.
Wall Mount
Backplate
A
Light
Light
On
On
Adjust
Adjust
Off
Off
LUTRON
LUTRON
Light
On
Adjust
Off
Off
LUTRON
LUTRON
Made and Printed in U.S.A. 10/09 P/N 030-1126 Rev. A
Advertisement
