Download
Share
Print this page
Steelcase 9000 Series Manual
  1. Manuals
  2. Brands
  3. Steelcase Manuals
  4. Adapter
  5. 9000 Series
  6. Manual
Steelcase 9000 Series Manual

Steelcase 9000 Series Manual

Desk adapter kit (used for mounting 22-5/8" d pedestals under 30"d desks)
Hide thumbs
1
2
3
4
5
6
7

Advertisement

Quick Links

Download this manual
®
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©
2003 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
(Used for Mounting 22-5/8" D Pedestals Under 30"D Desks)
NOTE: For pedestals manufactured prior
to February 2004, use adapter kit 99239
per assembly direction 939501141.
®
Series 9000
Desk Adapter Kit
Components
Tie Plate
Adapter Bracket
Back Panel
Retainer
#10 x 1/2" Self
Drilling Screw
(GQTFC)
1/4-20 x 1/2"
Hex Head Screw
(853014765MP)
For Package of all
Components above
(9U239)
3/8" HEX
SOCKET
#2 PHILLIPS BIT
Page 1 of 7
939503251 Rev C

Advertisement

loading

Related Manuals for Steelcase 9000 Series

Summary of Contents for Steelcase 9000 Series

  • Page 1 (GQTFC) If you have a problem, question, or request, call #2 PHILLIPS BIT 1/4-20 x 1/2" your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) NOTE: For pedestals manufactured prior Hex Head Screw for immediate action by people who want to help you.
  • Page 2 OUTER END PANEL ACCESS CAP Remove outer end panel. Remove access cap by pulling upward on the left end cap (1a). With your finger, move the exposed release tab disengaging top of outer end panel (1b). With the top of outer end panel tilted outward, lift up removing the bottom tabs (1c).
  • Page 3 ADAPTER BRACKET Attach adapter brackets to worksurface channels using two (2) #10 x 1/2" self-drilling screws (GQTFC) per bracket. #10 X 1/2" SELF-DRILLING SCREW (GQTFC) Page 3 of 7 939503251 Rev C...
  • Page 4 3/4” HEIGHT BACK PANEL BACK PANEL RETAINER necessary, relocate back 1/4-20 x 1/2" HEX HEAD SCREW panel to the recessed position. (853014765MP) Secure back panel to worksurface using the tie plate and three (3) #10 x 1/2" self-drilling screws (GQTFC). FULL HEIGHT BACK PANEL #10 X 1/2"...
  • Page 5 Removal of Drawers Pull drawer forward. Remove remaining drawers. TIP: Mark all drawers so they can be Push on tab on each side of the easily re-installed in their original drawer rails. positions. Remove drawer completely. Remove hanger bracket. Push drawer rails back into pedestal.

  • Page 6: Pedestal Installation

    Pedestal Installation Attach pedestal to worksurface and adapter brackets using five (5) 1/4-20 x 1/2" hex head screws (853014765MP) as shown. Flip desk back over and replace end panel covers. Adjust end panel glides to level the worksurface. Bottom View of Pedestal Showing Screw Locations (Back) (Front)
  • Page 7 Drawer Re-Assembly NOTE: Remember to re-install drawers in their original positions. Verify that drawer rails are pushed back into pedestal. Pull ball cages on drawer rails to front of drawer rails. Carefully align drawer portion of rail with ball cage of pedestal portion of rail and gently push drawer back into pedestal.