General - Kenwood TK-3200L Service Manual

TK-3200L
INTRODUCTION
SCOPE OF THIS MANUAL
This manual is intended for use by experienced technicians
f a m i l i a r w i t h s i m i l a r t y p e s o f c o m m e r c i a l g r a d e
communications equipment. It contains all required service
information for the equipment and is current as of the
publication date. Changes which may occur after publication
are covered by either Service Bulletins or Manual Revisions.
These are issued as required.
ORDERING REPLACEMENT PARTS
When ordering replacement parts or equipment information,
the full part identification number should be included. This
applies to all parts, components, kits, or chassis. If the part
number is not known, include the chassis or kit number of
which it is a part, and a sufficient description of the required
component for proper identification.
TK-3200L (ProTalk)
Destination Number of CH
K 2-channel
K2 8-channel
K3 15-channel
2

GENERAL

Frequency No. / Frequency
CH1 464.5000MHz CH29
CH2 464.5500MHz CH30
CH3 467.7625MHz CH31
CH4 467.8125MHz CH32
CH5 467.8500MHz CH33
CH6 467.8750MHz CH34
CH7 467.9000MHz CH35
CH8 467.9250MHz CH36
CH9 461.0375MHz CH37
CH10 461.0625MHz CH38
CH11 461.0875MHz CH39
CH12 461.1125MHz CH40
CH13 461.1375MHz CH41
CH14 461.1625MHz CH42
CH15 461.1875MHz CH43
CH16 461.2125MHz CH44
CH17 461.2375MHz CH45
CH18 461.2625MHz CH46
CH19 461.2875MHz CH47
CH20 461.3125MHz CH48
CH21 461.3375MHz CH49
CH22 461.3625MHz CH50
CH23 462.7625MHz CH51
CH24 462.7875MHz CH52
CH25 462.8125MHz CH53
CH26 462.8375MHz CH54
CH27 462.8625MHz CH55
CH28 462.8875MHz CH56
PERSONAL SAFETY
The following precautions are recommended for personal
safety:
● DO NOT transmit until all RF connectors are verified secure
and any open connectors are properly terminated.
● SHUT OFF and DO NOT operate this equipment near
electrical blasting caps or in an explosive atmosphere.
● This equipment should be serviced by a qualified technician only.
SERVICE
This transceiver is designed for easy servicing. Refer to
the schematic diagrams, printed circuit board views, and
alignment procedures contained within.
Default CH setting
462.9125MHz
CH1: 464.5500MHz / QT 67.0Hz
464.4875MHz
CH2: 467.9250MHz / QT 67.0Hz
464.5125MHz
464.5375MHz
CH1: 464.5500MHz / QT 67.0Hz
464.5625MHz
CH2: 467.9250MHz / QT 67.0Hz
466.0375MHz
CH3: 461.0375MHz / QT 67.0Hz
466.0625MHz
CH4: 461.0625MHz / QT 67.0Hz
466.0875MHz
CH5: 461.0875MHz / QT 67.0Hz
466.1125MHz
CH6: 461.1125MHz / QT 67.0Hz
466.1375MHz
CH7: 461.1375MHz / QT 67.0Hz
466.1625MHz
CH8: 461.1625MHz / QT 67.0Hz
466.1875MHz
466.2125MHz
CH1: 464.5500MHz/QT 67.0Hz
466.2375MHz
CH2: 467.9250MHz/QT 67.0Hz
466.2625MHz
CH3: 461.0375MHz/QT 67.0Hz
466.2875MHz
CH4: 461.0625MHz/QT 67.0Hz
466.3125MHz
CH5: 461.0875MHz/QT 67.0Hz
466.3375MHz
CH6: 461.1125MHz/QT 67.0Hz
466.3625MHz
CH7: 461.1375MHz/QT 67.0Hz
467.7875MHz
CH8: 461.1625MHz/QT 67.0Hz
467.8375MHz
CH9: 464.5000MHz/QT 67.0Hz
467.8625MHz
CH10: 467.7625MHz/QT 67.0Hz
467.8875MHz
CH11: 467.8125MHz/QT 67.0Hz
467.9125MHz
CH12: 467.8500MHz/QT 67.0Hz
469.4875MHz
CH13: 467.8750MHz/QT 67.0Hz
469.5125MHz
CH14: 467.9000MHz/QT 67.0Hz
469.5375MHz
CH15: 461.1875MHz/QT 67.0Hz
469.5625MHz
RF power output
2W