Kenwood TK-3200L Service Manual page 5

TK-3200L
4-5. Programming software KPG-88D description
KPG-88D is the programming software for the transceiver
supplied on a CD-ROM. This software runs under Windows 98,
ME, Windows 2000 or XP on an IBM-PC or compatible machine.
The data can be input to or read from the transceiver and
edited on the screen. The programmed or edited data can be
printed out. It is also possible to tune the transceiver.
IBM-PC
KPG-88D
RF Power meter
or SSG
PC
D-SUB
(25-pin)
KPG-22
Transceiver
5. Clone Mode
5-1. Outline
"Clone Mode" copies the transceiver data to another
transceiver.
The dealer can copy the transceiver data to another
transceiver even without the use of a personal computer.
5-2. Example
The transceiver can copy the programming data to one or
more transceivers via RF communication.
The clone source and clone target/s must be in Clone mode.
5-3. Operation
1. To switch the clone target/s to Clone mode, press and hold the
[PTT] and [Side2] keys while turning the transceiver power ON.
2. Wait for 2 seconds. The LED will light orange and the
transceiver will announce "Clone".
3. Select a channel table number using Side1(increment
channel table) and Side2(decrement channnel table) keys.
4. To switch the clone source to Clone mode, press and hold the
[PTT] and [Side2] keys while turning the transceiver power ON.
5. Wait for 2 seconds. The LED will light orange and the
transceiver will announce "Clone".
6. Select the same channel table number as the clone target/s.
7. Press [PTT] on the clone source to begin data transmission.
When the clone target starts to receive data, the LED will
light green.
4
REALIGNMENT
KPG-22 or KPG-22A or KPG-22A + KCT-53U
Illustration is KPG-22.
Gray
Gray/Black
1.5D-XV Lead wire
1.5D-XV Shield wire –
Tuning cable
(E30-3216-05)
PC PC
D-SUB
USB
(9-pin)
KCT-53U
KPG-22A
KPG-22A
Transceiver Transceiver
Fig. 1
When the clone source finishes sending data, a
"confirmation" tone will sound.
If data transmission fails while cloning, an "error" tone will
sound from the Target unit.
8. If the cloning fails, no data will be available in the Target
unit when it is returned to User mode.
9. When the cloning is successful, the Target unit's "Scan"
function will return to its default value (Scan = OFF).
Notes:
• The dealer can clone data to two or more transceivers by
repeating the above procedures.
• If the transceivers Clone Mode is configured as "Disabled",
+
}
SP
–
the transceiver cannot enter Clone mode.
+ }
MIC
• The table shown below will cover the frequency tables used
for wireless cloning.
• A unit cannot be a "Source Unit" if it is unprogrammed. If
[PTT] is pressed, an "error" tone will sound.
• Once a unit is set to be the Source, it cannot be a target
after the data has been transmitted. This protects the data
in the Source unit.
• If the Target unit is cloned successfully, it will return to User Mode.
• If the Target unit is not cloned successfully, the led will
remain Orange.
• The Source Unit and Target Unit must be of the same model
type and destination in order for Clone to operate.
• Clone mode cannot be accessed if "Super Lock" is activated.
• Electronic interface may cause a failure in data transfer
during Wireless Clone, such as when waveforms or
electromagnetics are being performed at the workbench.
• Clone mode can be used ONLY by the authorized service
personnel.
• The Clone mode setting must be configured as "Disable"
before being delivered to the end-user.
• To clone, replace the antenna from both the source
transceiver and the target transceiver with a dummy load.
• The transmit output power is automatically set to Low
in Clone mode.