Advertisement
SPECIFICATIONS
System overall
Working range.............................................IRB-10 – 1600 ft
Frequency response ...................................50Hz – 9kHz (±3dB) body pack (mic dependent)
Dynamic range............................................>100dB
Operating temperature range .....................32
Noise reduction ...........................................2:1 log compander
IRR-10 1-channel receiver
Sub-carrier frequencies ..............................2.06MHz or 2.56MHz
Type ............................................................super heterodyne – crystal controlled
Modulation...................................................FM
Signal-to-Noise ...........................................>90dB
Image rejection ...........................................>40dB
Reception sensitivity ...................................>25dBμV
Reception selectivity ...................................±40kHz
Audio output adjustment.............................line:+4dB max
Audio output impedance.............................line:<1k ohms
Power requirement......................................12VAC @ 1.6A
Size .............................................................5.55" W x 5.1" D x 0.95" H (141 x 129.5 x 24mm)
Weight .........................................................11oz (311g)
IRB-10 – 2-channel body pack transmitter
Sub-carrier frequencies ..............................2.06MHz & 2.56MHz switchable
Modulation...................................................FM
Audio distortion ...........................................< 1.0% (±40kHz deviation @ 1kHz)
Mic input impedance...................................2.2k ohms
Mic input jack ..............................................3.5mm
Built-in auxiliary mic ....................................uni-directional electret
Mic gain adjustment....................................Max to –50dB
Battery type.................................................2-"AA" alkaline (2 x 1.5V)
Battery life
(100mA drain) ......................> 15 hours w/alkaline batteries – low power mode
(160mA drain) ......................> 10 hours w/alkaline batteries – high power mode
Size .............................................................3.94" H x 2.52" W x 1.06" D (100 x 64 x 27mm)
Weight .........................................................4.65oz (132g) – transmitter (w/alkaline batteries)
IRH-10 – 2-channel handheld transmitter
Sub-carrier frequencies ..............................2.06MHz & 2.56MHz switchable
Modulation...................................................FM
Audio distortion ...........................................< 1.0% (±15kHz deviation @ 1kHz)
Microphone element type ...........................uni-directional dynamic
Battery type.................................................2-"AA" alkaline (2 x 1.5V)
Battery life (260mA drain)...........................> 10 hours w/alkaline batteries
Size .............................................................10.04" x 2.28" (255 x 58mm)
Weight .........................................................9.1oz (258g) w/alkaline batteries)
IRD-10 external sensor
Cable length................................................32.8' (10m)
Power ..........................................................powered by receiver
Size .............................................................2" W x 3" W x 1" H (50.8 x 76.2 x 25.4mm)
Weight .........................................................4oz (113.4g)
Mounting
Due to constant improvements, specifiations are subject to change without notice.
6
2
w/built-in sensor
IRH-10 – 2500 ft
w/built-in sensor
2
50Hz – 5kHz (±3dB) auxiliary emitter mic
40Hz – 9kHz (±3dB) handheld
o
~ 113
o
F (0
o
~ 45
o
C)
2-"AA" rechargeable Ni-MH or Ni-Cd (2 x 1.2V)
1.34oz (38g) – clip-on emitter
2-"AA" rechargeable Ni-MH or Ni-Cd (2 x 1.2V)
1- Azden AN-2A rechargeable Ni-Cd
included metal bracket
INTRODUCTION
Thank you for selecting the Azden "RED" infrared system as your wireless solution. We are
confident that it will perform beyond your expectations. For over 40 years Azden Corpora-
tion has been creating technologically advanced products. By taking advantage of the latest
in CAD design and SMT production techniques, Azden's engineers are able to produce
products that exceed the published specifications and perform well beyond the warranty
period.
Azden "RED" represents a breakthrough in wireless. Instead of the normal radio waves that
other wireless systems use, Azden "RED" uses invisible light beams in the infrared range.
Through the use of infrared you will no longer be plagued by outside interference. "RED's"
enhanced performance assures you of the finest in audio clarity and reliability. The specially
selected high-frequencies provide you with trouble free performance, even in fluorescently
lit rooms. Like all infrared, Azden "RED" will not operate correctly outside in the sunlight.
In the real world, the ability to use multiple systems in the same location without frequency
interference will prove to be a tremendous benefit to you. Using infrared means that the
audio generated in your room stays in your room. Your discussions cannot be overheard on
other systems in other rooms.
Designed by professionals - for professionals, Azden "RED" will provide you with years of
worry-free, high-quality performance.
ii
Advertisement
