Related Manuals for Ganz VCOUNT700RP
Summary of Contents for Ganz VCOUNT700RP
- Page 1 Instruction Guide Configuration of GANZ IP (VCA) counters with VCOUNT700RP unit Rev. 05.2015 People Counting System...
-
Page 2: Table Of Contents
VCOUNT700RP server configuration ……………………………………………... 1.1. Network settings (IP address) ..…………………………………………………………………. 1.2. Logging ……………………………….……………………………………………………………………. Counter configuration …………………………………………………………………………… 2.1. Data transmission to VCOUNT700RP server ……..………………………………………. 2.2. HTTP Server on GANZ GXi devices…………………………………………………………….. 2.3. Setup of counters in Camera/encoder ……………………………………………………… 2.4. Setup of VCOUNT700RP Gates …………………………………………………………………. -
Page 3: Vcount700Rp Server Configuration
‘Raspberry Pi’, and its IP/MAC address is shown as well (you can find also MAC address printed on label of VCOUNT700RP unit). 1.2 Logging in To login to the VCOUNT700RP system, you need to enter its IP address into a n y web browser, and then enter the default ID and password. ID: cbc... -
Page 4: Counter Configuration
CONFIGURATION - INSTR. MANUAL 2. Counter configuration 2.1 . Data transmission to VCOUNT700RP server VCOUNT700RP server is working in a system under ‘listening’ mode, and each single VCA device (counter) initiates data transmission through the network to VCOUNT700RP server. In order to ensure proper data transmission flow in the system, you need to setup VCA Event Configuration, as below: “SETUP →... - Page 5 PEOPLE COUNTING SYSTEM CONFIGURATION - INSTR. MANUAL In section “Second Event”, deactivate “DI” and “DO”. Please note second event is not available for ZN-XE, ZN1, ZS1 series devices. 040515...
-
Page 6: Http Server On Ganz Gxi Devices
2.2: 2.2. HTTP Server on GANZ GXi devices In order to activate data sending from VCA device to the VCOUNT700RP server, you need to define the IP address of the VCOUNT700RP server in VCA device. -
Page 7: Setup Of Counters In Camera/Encoder
E.g. if last counters of CAM.1 are named: in5/out5, the first counters of CAM.2 have to be named: in6/out6. VCOUNT700RP supports up to 16 counter pairs, so that last counter pair will be in16/out16. NOTE: it is possible to use counter based on VCA rules different from counting line, considering that it is mandatory to: Create incremental counter based on any single rule. -
Page 8: Setup Of Vcount700Rp Gates
X identifies counter name set on GXi device. There are no limitation on gates number that can be created into VCOUNT700RP server, in order to let user configure as many gates as needed. -
Page 9: Setup Of Vcount700Rp Reports
PEOPLE COUNTING SYSTEM CONFIGURATION - INSTR. MANUAL 2.5. Setup of VCOUNT700RP Reports Counters are visualized into Report menu page. Create a New set of Report by selecting ‘A new set of’ into Gates drop down box, as per below snapshot. - Page 10 PEOPLE COUNTING SYSTEM CONFIGURATION - INSTR. MANUAL It is possible to select report time range and type of report (from quarter of an hour to monthly) in order to visualized counters as needed. It is possible to show report into browser in table or chart mode, otherwise it is possible to export it to Excel by selecting desired view from ‘Show’...
- Page 11 PEOPLE COUNTING SYSTEM CONFIGURATION - INSTR. MANUAL Daily report of a week in table mode. 040515...
-
Page 12: Network Settings Of Vcount700Rp Server
CONFIGURATION - INSTR. MANUAL 3. Network settings of VCOUNT700RP unit In order to set the static IP address of VCOUNT700RP unit, you need to login into configuration interface of network card, it is enable with port number 10000, by using... - Page 13 PEOPLE COUNTING SYSTEM CONFIGURATION - INSTR. MANUAL Change IP from DHCP to Static Here you can select IP address mode from DHCP to Static: Save to confirm selection. 040515...
- Page 14 PEOPLE COUNTING SYSTEM CONFIGURATION - INSTR. MANUAL CBC (Poland) sp. z o.o. Anny German 15 01-794 Warszawa Tel. +48 22 633 90 90 040515...