Advertisement
Settings
After finishing the installation, make various settings.
Preparation
Please check the number of cylinders and cycles for the model car being used.
A
Cylinder Number Setting
SETTING
Set the cylinder number for the car being used.
The number of cylinders is set by the shift lamp pattern.
1
OFF
Press the
switch
Press the switch with the
ignition in the OFF position
(meter light off)
2
ENGINE
START
While holding the switch, start
the engine within 5 seconds.
4
5
6
-cylinder
Turn
Patterns for cylinder settings display
Number of
Shift lamp
Car models
cylinders
1
NISSAN (FAIRLADY Z Z33) / MAZDA (ATENZA and others)
2
MAZDA (RX-8) / SUBARU (early type of PLEO and others)
Note 1: For one and two cylinder engines,
set the signal level switch to two.
3
Three-cylinder
4
Four-cylinder and Rotary engine (RX-7)
5
Five-cylinder
6
Six-cylinder
8
Eight-cylinder
A
Some models of NISSAN
Special
Reference: If the engine is a two cycle engine, multiply the number of cylinder by two.
(e.g., For a two-cycle three-cylinder engine the setting would be six.)
With no operation
6
for 5 seconds
B
Switching the Display
SETTING
Switching the Chronometric / Real-time Display.
1
Press the
switch once
While the tachometer is being
displayed, press the switch once.
3
Press the
switch
Pressing the switch changes
the display mode.
4
With no operation
for 5 seconds
C
Peak reading display and re-set
SETTING
Display Peak reading and reset the value.
1
Press the
switch once
While the tachometer is being
displayed, press the switch once.
2
Peak reading
display
3
Press the switch
for 2 seconds
Pressing the switch will re-set the
peak reading.
3
Opening Demo
4
Cylinder
display
Shift Lamp ON
(The factory default setting is for a
four-cylinder engine)
5
Press the
switch once
Press the switch to change the
pattern and set to the proper one.
8
A
1
2
Special
= On
= Blink
⇒
See
SETTING F
for details.
7
Tachometer display
Press
(Chronometric/ Real-time)
2
Peak reading
display
＋
Shift Lamp ON (Setting)
Real-time
Chronometric
Shift Lamp changes by pressing the switch.
5
Tachometer display
Press
4
The needle will show "0"
All shift lamps will light
5
Tachometer display
D
Shift Point Setting
SETTING
Make RPM setting for turning on the shift lamp. (Setting Range: 3000–9000rpm)
1
W h i l e t h e t a c h o m e t e r i s b e i n g
displayed, press the switch for long.
3
Press the
switch
While holding down the
switch, change the RPM setting
4
With no operation
for 5 seconds
3
E
Shift lamp brightness setting
SETTING
= Off
Make setting to change the shift lamp brightness.
(It will be the minimum brightness if Orange cable is wired to parking light.)
1
W h i l e t h e t a c h o m e t e r i s b e i n g
displayed, press the switch for long.
3
Press the
switch
While holding down the switch,
change the brightness setting.
4
With no operation
for 5 seconds
F
Switching the signal level
SETTING
Changes are only necessary for those car models listed below.
NISSAN (FAIRLADY Z Z33)/ MAZDA (after 2002)/ MITSUBISHI (COLT and others)
/SUBARU (early type of PLEO and others)
1
The ignition OFF
OFF
(Meter light Off)
Press the switch with the ignition in
the OFF position (meter light off).
ON
Turn the ignition to
the ON position
(engine not running)
Press the switch
for 5 seconds
2
Opening Demo
4
Press the
switch
Set the signal detection level
by p r e s s i n g t h e sw i t c h to
change the needle position
to the correct setting.
5
With no operation
for 5 seconds
Press for 1.5 seconds
2
The needle will show the
Press the switch
set shift point
for 1.5 seconds
The lamps blink red
Each pressing of the switch will
raise, the set ting 20 0 rpm; at
peak it will return to 3000 rpm.
Note: By continually pressing down on
the switch the needle will move to peak.
5
Tachometer display
Press for 3 seconds
2
Af ter 1. 5 seconds the shif t
Press the switch
point will be shown and after
for 3 seconds
3 seconds all lamps will light
All shift lamps will light
5 steps
Bright
Each pressing will decrease the brightness;
when pressed at the darkest setting it will
return to the brightest possible setting.
5
Tachometer display
Press for 5 seconds
⇒
See the "Wiring Chart" for details.
Press the
switch
Keep pressing the switch
3
The needle will show "1" or "2"
The lamps blink red
1
2
= If the generic car
1
1
6
Tachometer display
The needle will show "0"
Dark
= If the level is small
2
2
3
Advertisement
