Advertisement
Connecting The Wires
Basic Wiring
5-pin
Backside
connector
of the Meter
IGN
Connect to the IGN (12V with key
Red
s w i t c h O N ) u s i n g t h e c u t
connectors(included).
Earth
Fasten to a screw of a
with earth
Black
m e t al p a r t which is
terminal
earthed.
• Painted screws and screws connected to
plastic parts are not earthed; make sure to
connect only to a place which is earthed.
When another device is already connected
to the RPM signal from the ECU
To get the RPM signal from other than the ECU
• To get the RPM signal from diagnosis
(check connector)
e.g.) in case of
MAZDA EUNOS
ROADSTER (NA6C)
White
←To meter
e.g.) Genuine tachometer of a six-cylinder car
If display the extremely
displays the 500rpm at the 3000rpm. The reason
low number of RPM by
is that the car is independent ignition type.
above connecting
[Reference]
1
How to use the Cut
Connectors
Peel off of the vinyl
cover at connection.
Installing The Product
A. Installation with the Adjustable Stand
Fasten using the double-sided tape. (On top of the steering column cover or dashboard.)
1
Slightly loosen the Hex-
agonal bolt and install the
gauge into the Adjustable
Stand.
Adjustable
Stand
Hexagonal
bolt
Can be mounted in
various places
Mount almost anywhere
using the double -sided
tape. After mounting it is
possible to for easy-read-
ing.
2
IGN
(12V with key switch ON)
( 1.5 m)
Red
( 1.5 m)
Black
( 1.5 m)
White
(See Note on the right)
RPM Signal
Confirm the positions on the
White
" W i r i n g C h a r t " a n d t h e n
connect the wire using the cut
connectors (included).
Wiring
Chart
• Make sure to connect the white wire to
indicated place on the car.
▶ and that device works properly keep that wiring.
▶ and the meter or other device stops working properly or sometimes becomes unstable
Location of
the RPM signal
(IG − )
10 mm
2
10 mm
Peel off of the vinyl
cover at the end of
the product' s wire.
2
Fasten using the double-sided
t a p e . (C l e a n t h e s u r f a c e;
removing all oil and dust.)
Double-sided
tape (Included)
Clean to remove
oil and dust
Note: Please be sure about where you
wish to install the meter, as it is not
advisable to reuse double-sided tape.
On the dashboard
On the steering
On the steering
column cover
column cover
: Cut Connector
ECU
Engine Computer,
etc.
TA
Earth
disconnect from the ECU wire and get the RPM from the minus terminal of ignition coil or
diagnosis. ⇒
See following "To get the RPM signal from other than the ECU"
• To get the RPM signal from the
ignition coil
ー
White
←To meter
Ignition coil
Set the Cylinder Number setting to "1" .
⇒ See page 3
Connection for Cylinder Number Setting
3
4
Close tightly with cut
Wrap around both
connector.
wire coils.
Install in an easy-to-view location.
3
A f t e r d e c i d i n g t h e
position and angle of the
meter face, fasten the
Hexagonal bolt on both
sides to secure.
Hexagonal
bolt
Meter
17.5
23.5
Dimensions
(unit; mm)
ø92
Note:
If the White wire is not long enough,
please use the white wire
in this package to extend the length.
Cut
White
connector
extension wire
⇒ See [Reference 1] How to use the Cut
Connectors on Page 2.
Dimming Shift Lamp along with parking lights
This wiring is to use the lowest brightness for
Orange
the shift lamp when only the parking lights are
(Not normally
on; hence neither the dial or the needle will
required)
be it up when running with parking lights on.
Cut the black tube of the wire tip and connect.
5-pin
Backside
connector
of the Meter
Orange
• To get the RPM signal from the ignition signal of
the direct ignition coil
Direct Ignition coil
Ignition signal
White
←To meter
Note : Set the Cylinder Number setting to "1". Make sure to
check the wiring position of the ignition signal which will vary
depending on the car models.
5
I n s u l a t e w i t h v i n y l
tape.
B. Mount into the Panel
1
Wrap the cushion tape around the base
of the meter.
2
Press into the 80 mm hole in the panel.
Cushion
tape
Note:
If you wish to open holes
to fasten the unit to the pillar or
column cover, please purchase
and use the separately sold pillar
holder.
ø80
Pillar holder for ø80
PH-80
provided
( 1.5 m)
Insulate the cut off
part with tape
Parking light
(12V with
parking light
ON)
: Use cut connector
Note: When crimping,
please use crimpers or
use pliers to bend and
then solder together.
Panel
A pillar
Screw
hole
Pillar
holder
Advertisement
