Advertisement
Quick Links
Advertisement
Related Manuals for Fortis MAGNETIC FLYWHEEL FXT-330
Summary of Contents for Fortis MAGNETIC FLYWHEEL FXT-330
- Page 1 MAGNETIC FLYWHEEL ELLIPTICAL CROSS TRAINER (FXT-330) FSMFEXT330A...
-
Page 3: Safety And Warnings
SAFETY & WARNINGS Read all of the instructions in this guide before using this product. Retain this guide for future reference. Do not skip, substitute or modify any steps or procedures in this guide, as doing so could result in personal injury or product damage. •... - Page 4 • Be careful when lifting and moving the equipment. Always use proper lifting technique and seek assistance if necessary. • Your equipment is intended for use in cool, dry conditions. You should avoid storage in extreme cold, hot or damp areas as this may lead to corrosion and other related problems.
- Page 5 OVERVIEW...
- Page 6 Part Description Qty. Part Description Qty. Bolt M8 x 20 x S6 Universal joint Washer d5 x Φ10 x 1.0 Spring washer d8 Washer d8 x Φ20 x 2 Nut 9/16 x 20 x H9 x S19 Front stabiliser Bolt M8 x 45 x 20 x S14 Main frame Pedal (L/R) Rear stabiliser...
- Page 7 Part Description Qty. Part Description Qty. Handle pulse Nut M10 x H9.5 x S17 Screw ST4 x 19 x Φ7 Bolt M8 x 75 x 13 x S14 Plug Φ12 x 11 x Φ3 Plug Φ18 x 3 x Φ14 x 7 x Φ10.1 Bushing 4Φ32 x 3.5 x Φ28 x End cap J60 x 30 x 15 20.5 x Φ19.1...
- Page 8 ASSEMBLY Step 1: Secure front stabiliser ( 4 ) and rear stabiliser ( 6 ) to the mainframe ( 5 ) with bolt ( 1 ), spring washer ( 2 ) and washer ( 3 ).
- Page 9 Step 2: Remove the pre-installed bolt ( 8 ) and washer ( 3 ) from the mainframe ( 5 ) , please reserve for upcoming step. Connect the wire of tension control ( 9 ) with Tension control wire ( 11 ). Connect trunk wire ( 10 ) with sensor wire ( 12 ).
- Page 10 Step 3: Insert the swing rod ( 16L/R ) to the hand bar post ( 7 ) separately. Fix them with bolt ( 14 ), spring washer ( 2 ) and washer ( 15 ), then attach end cap ( 13 ); Put the bolt ( 18L/R ) and wave washer ( 19 ) through the Universal joint ( 20 ), fix them to the crank ( 17L/R ) with nut ( 22L/R ) separately.
- Page 11 Step 4: Secure pedal ( 24L/R ) to pedal supporting rod ( 63L/R ) with bolt ( 23 ), washer ( 25 ) and nut ( 26 ) separately.
- Page 12 Step 5: Insert handlebar ( 27L/R ) to swing rod ( 16L/R ) separately. Secure the handlebar ( 27L/R ) with bolt ( 28 ), arc washer ( 29 ) and nut ( 30 ).
- Page 13 Step 6: Connect Console wire ( 35a ) with trunk wire ( 10 ) and then secure Console ( 35 ) to the handlebar post ( 7 ) with bolt ( 36 ). Remove the pre-installed bolt ( 32 ) and spring washer ( 2 ) from the handlebar post ( 7 ). Reserve them for the next step.
- Page 14 FUNCTIONS 1. SCAN Press MODE button until “SCAN” appears, the computer will rotate through all the 5 functions: Time, Speed, Distance, Calorie and pulse. Each display will be held for 6 seconds. 2. SPEED Display instantaneous speed and the range is 0.0~999.9km/h. 3.
- Page 15 BUTTONS 1. MODE • Press this button to changeover display or choose the window needs to be set. 2. SET • In setting status, press this button to increase setting value in relevant flashing window for TIME, DIST, CAL and PULSE. 3.
- Page 16 Need more information? We hope that this user guide has given you the assistance needed for a simple set-up. For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com...