Draper FlexShade 2 Pocket Headbox Instructions Manual
  1. Manuals
  2. Brands
  3. Draper Manuals
  4. Indoor Furnishing
  5. FlexShade 2 Pocket Headbox
  6. Instructions manual
Draper FlexShade 2 Pocket Headbox Instructions Manual

Draper FlexShade 2 Pocket Headbox Instructions Manual

Maximized coverage for large, tall areas, while also reducing light gap
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
FlexShade
®
Maximized coverage for large, tall areas, while also reducing light gap

Overview - Components

Contents
Overview - Components .......................................................................................1
Section 1 - Mounting Shade ................................................................................3
Section 2 - Removing/Replacing Roller ............................................................4
2 Pocket Headbox
PERSONNEL REQUIRED
1
2
Section 3 - Replacing Shade/Motor Assembly ................................................4
Section 4 - Bottom Closure Removal/Replacement .......................................5
Section 5 - Operation............................................................................................5
Section 6 - Electrical Connections .....................................................................6
Section 9 - Dimensions ........................................................................................8
© 2021 All Rights Reserved
INSTRUCTIONS
INSTALLATION & OPERATION
TOOLS REQUIRED
TAPE MEASURE
PENCIL
PLIERS
POWER DRILL
CAUTION
Read and understand all warnings
before beginning installation.
If you have any difficulties installing or servicing your
FlexShade 2, call your dealer or Draper, Inc.
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
|
FORM: FS_MO_FS2_PHB_Inst21
LEVEL
HARDWARE
(by others)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FlexShade 2 Pocket Headbox and is the answer not in the manual?

Questions and answers

Related Manuals for Draper FlexShade 2 Pocket Headbox

Summary of Contents for Draper FlexShade 2 Pocket Headbox

  • Page 1: Table Of Contents

    Section 9 - Dimensions ..................8 If you have any difficulties installing or servicing your FlexShade 2, call your dealer or Draper, Inc. Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385 draperinc.com | 765.987.7999 | 800.238.7999 FORM: FS_MO_FS2_PHB_Inst21 © 2021 All Rights Reserved...

  • Page 2: Please Read - Important Installation And Safety Information

    Most standard Draper fabrics may be cleaned at the window by vacuuming with a soft brush attachment. They also may be cleaned by using a sponge or soft cloth and mild solution of warm soapy If the shade is telescoping, place a piece of shimming water.

  • Page 3: Section 1 - Mounting Shade

    FlexShade 2 Pocket Headbox ® page 3 of 8 Section 1 - Mounting Shade Caution: Before mounting shades, verify measurements on label provided with shade, and ensure unit is installed at correct width. Please Note: Installer is responsible for selecting mounting hardware appropriate for site conditions. 1.

  • Page 4: Section 2 - Removing/Replacing Roller

    FlexShade 2 Pocket Headbox ® page 4 of 8 Section 2 - Removing/Replacing Roller Figure 1 INTERNAL WIRING Shade roller removed for clarity If there is not sufficient access above the ceiling to access the end plates, use the knockouts located in the top of the case just below the mounting bracket holes.

  • Page 5: Section 4 - Bottom Closure Removal/Replacement

    AT NO TIME SHOULD SHADE BE UNROLLED ENOUGH TO EXPOSE ANY PART OF SHADE ROLLER. Please Note: The above instructions affect only the limits on standard motors. For adjustment procedures using RTS, RS485, or Draper’s IntelliFlex I/O Control Systems, please consult the installation information on the Draper website for the appropriate control.

  • Page 6: Section 6 - Electrical Connections

    (es) (es) attached wiring diagram, and wiring should comply with national and local electrical codes. DO NOT wire motors in parallel without written permission from Draper. All operating switches should be “off” before power is connected. Please Note: For low voltage wiring requirements, Draper recommends consulting with a professional low voltage electrical contractor. It is very important that shielded and stranded CAT 5 cable be used to prevent any electrical interference.
  • Page 7 120V off and switch the red and black wires from the motor to the switch. Do not wire motors in parallel without written permission from Draper. M12 Connector Connector Dashed Wiring by Electrician Telis 1...

  • Page 8: Section 9 - Dimensions

    FlexShade 2 Pocket Headbox ® page 8 of 8 Section 9 - Dimensions " (17mm) " (19mm) WARNING 6 " Do not lift case in center. (165mm) Lift at ends only to avoid damage to case and surface. .034" (8.6mm) Shade Width "...

Table of Contents