Subscribe to Our Youtube Channel
Related Manuals for ASSEMBLAD HDL-113
Summary of Contents for ASSEMBLAD HDL-113
- Page 1 HEADLIGHT TESTER HDL-113 OPERATION AND MAINTENANCE MANUAL Note Edition RAEE: November 2018 - Vers. 1.20 ASSEMBLAD – Automotive Division - Technical dept...
- Page 2 HDL-113 Operation and maintenance manual ASSEMBLAD S.r.l. Campi Bisenzio - Florence - Italy - Tel. +39 055-890485 www.assemblad.com - E-mail: info@assemblad.com...
-
Page 3: Table Of Contents
1.1 TAKING OVER ....................4 1.2 SECURITY RULES ..................4 2 TECHNICAL DATA ..................5 2.1 LIST OF PARTS OF HEADLIGHT TESTER MODEL HDL-113 ...... 5 2.2 MEASUREMENT RANGES ................6 2.3 STORAGE AND USE ENVIRONMENTS ............6 2.4 KEYBOARD AND DISPLAY ................6 3 INSTALLATION .................... -
Page 4: General Information
Check the outside of the instrument, in case of damage due to transportation, note it to the carrier and promptly notifying the office of ASSEMBLAD shipments. Only with this procedure you can proceed with the integration of missing or damaged goods quickly. -
Page 5: Technical Data
HDL-113 Operation and maintenance manual 2 TECHNICAL DATA 2.1 LIST OF PARTS OF HEADLIGHT TESTER MODEL HDL-113 The parts of the instrument are the following: - Steel Base - Column with vertical displacement movement - Optical chamber with focal lens of 500 mm... -
Page 6: Measurement Ranges
Turn on the instrument Increase value or stand-alone test progress Decrease value or stand-alone test progress Confirm value or measure Turn off the instrument ASSEMBLAD S.r.l. Campi Bisenzio - Florence - Italy - Tel. +39 055-890485 www.assemblad.com - E-mail: info@assemblad.com... -
Page 7: Installation
- Set the column in vertical position with the screw displaced on the base (See under picture) Set the optical chamber for a planar position, verify the spirit level inside the optical chamber. ASSEMBLAD S.r.l. Campi Bisenzio - Florence - Italy - Tel. +39 055-890485 www.assemblad.com - E-mail: info@assemblad.com... -
Page 8: Software Installation
- Select the COM port connected to the instrument and select TEST CONNECTION - Select REGISTRATION and fill in all field with the garage and operator data ASSEMBLAD S.r.l. Campi Bisenzio - Florence - Italy - Tel. +39 055-890485 www.assemblad.com - E-mail: info@assemblad.com... -
Page 9: Operations
- Position the headlight tester with the lens at 50 cm from the headlight - Unblock the column - Turn on the line laser ASSEMBLAD S.r.l. Campi Bisenzio - Florence - Italy - Tel. +39 055-890485 www.assemblad.com - E-mail: info@assemblad.com... - Page 10 - Locate horizontal line of the vehicle, as the motor bonnet - Rotate the headlight tester until the laser line coincides with this line Set the column ASSEMBLAD S.r.l. Campi Bisenzio - Florence - Italy - Tel. +39 055-890485 www.assemblad.com - E-mail: info@assemblad.com...
-
Page 11: Line Laser Maintenance
2 screw, verify the cleaning of the laser lens. 4.4 OPTICAL CHAMBER ALIGNEMENT Using the side handle, align the camera taking as a reference the spirit level placed inside the optical chamber. ASSEMBLAD S.r.l. Campi Bisenzio - Florence - Italy - Tel. +39 055-890485 www.assemblad.com - E-mail: info@assemblad.com... -
Page 12: Optical Shield
The real value to set the vertical deviation is showed from the software in the selection of headlight type selection in the summary of vehicle data. ASSEMBLAD S.r.l. Campi Bisenzio - Florence - Italy - Tel. +39 055-890485 www.assemblad.com - E-mail: info@assemblad.com... -
Page 13: Test Run
Once you have aligned the instrument and set in plane, go to the left lighthouse. Insert the vehicle data, press CONFIRM (F3) ASSEMBLAD S.r.l. Campi Bisenzio - Florence - Italy - Tel. +39 055-890485 www.assemblad.com - E-mail: info@assemblad.com... - Page 14 Center the laser point with the center of left headlight Select START (F5) on PC PRESS START ON PC DATA RECEIVED Push “OK” on headlight tester PRESS OK ASSEMBLAD S.r.l. Campi Bisenzio - Florence - Italy - Tel. +39 055-890485 www.assemblad.com - E-mail: info@assemblad.com...
- Page 15 “OK” on the display. When you finish the measurement you can confirm with "OK", regardless the result of the test. ASSEMBLAD S.r.l. Campi Bisenzio - Florence - Italy - Tel. +39 055-890485 www.assemblad.com - E-mail: info@assemblad.com...
- Page 16 The measured values and confirmed will be displayed on the screen of LuxAnalyzer real- time software. HIGH BEAM LEFT Repeat for the high beam left ASSEMBLAD S.r.l. Campi Bisenzio - Florence - Italy - Tel. +39 055-890485 www.assemblad.com - E-mail: info@assemblad.com...
- Page 17 From this screen you can repeat the test or print the test report. With the exit button will automatically generated the file *.FAR. ASSEMBLAD S.r.l. Campi Bisenzio - Florence - Italy - Tel. +39 055-890485 www.assemblad.com - E-mail: info@assemblad.com...
-
Page 18: Metrological Logbook
In case the equipment is used for legal measurements, the logbook must be always updated, providing to perform the periodic and occasional checks and/or repairs, when needed, by Assemblad or by authorized personnel, C.S.R.P.A.D. of Rome, C.P.A. authorized by “Direzione Generale della Motorizzazione Civile e dei Trasporti in Concessione”, or by Notified Bodies. -
Page 19: Warranty
Assemblad or an authorized service center. 08 - Shipping charges shall be covered by the customer. 09 - ASSEMBLAD, even supplying support on demand for the first installation of the equipment, disclaims any liability for damages and injuries caused, even to third parties, by an improper installation, maintenance, defective or unsafe electrical connections. - Page 20 Via della Querce, 6a/6b 50013 Campi Bisenzio (Firenze) ITALY Tel. +39 055 890485 Fax +39 055 890496 All rights reserved No copies are permitted 2014/30/CE 2014/35/CE EN 61326-1 EN 61010-1 Are trade mark of Assemblad S.r.l. – Florence – Italy...
Need help?
Do you have a question about the HDL-113 and is the answer not in the manual?
Questions and answers