User's Manual - Ryobi EAG-7511 User Manual

GB
F D
THANK YOU FOR BUYING A RYOBI PRODUCT.
To ensure your safety and satisfaction, carefully read
through this OWNER'S MANUAL and the SAFETY
INSTRUCTIONS before using the product.
INSTRUCTIONS FOR SAFE HANDLING
Make sure that the tool is only connected to the
■
voltage marked on the name plate.
Never use the tool if its cover or any bolts are missing.
■
If the cover or bolts have been removed, replace them
prior to use. Maintain all parts in good working order.
Always secure tools when working in elevated positions.
■
Never touch the blade, grinding wheel or other
■
moving parts during use.
Never start a tool when its rotating component is in
■
contact with the work piece.
Never lay a tool down before its moving parts have
■
come to a complete stop.
ACCESSORIES: The use of accessories or
■
attachments other than those recommended in this
manual might present a hazard.
REPLACEMENT PARTS: When servicing use only
■
identical replacement parts.
ANGLE GRINDER SAFETY PRECAUTIONS
Check that the speed marked on the grinding wheel is
■
equal to or greater than the rated speed of the tool.
Ensure that the dimensions of the grinding wheel are
■
compatible with the tool and that the wheel fits
the spindle.
Grinding wheels must be stored in a dry place.
■
Grinding wheels must not be used for any operation
■
other than grinding.
Grinding wheels must be stored and handled with care
■
in accordance with the manufacturer's instruction.
Inspect the grinding wheel before use to ensure that it is
■
not chipped or cracked. Chips or cracks can cause the
wheels to shatter, resulting in possible serious injury.
Ensure that the wheel is fitted in accordance with
■
this manual.
Ensure that the grinding wheel is correctly mounted
■
and tightened before use and run the tool at no-load
speed for 30 seconds in a safe position. Stop
immediately if there is considerable vibration or if
other defects are detected. If this condition occurs,
check the tool to determine the cause.
Do not use separate reducing bushings or adapters to
■
adapt large hole grinding wheels.
E I P NL S DK N FIN GR
English
Check that the work piece is properly supported.
■
Use only grinding wheels approved by authorized
■
service centre
Ensure that sparks resulting from use do not create a
■
hazard e.g. do not hit people, or ignite flammable
substances.
Always use protective safety glasses and ear
■
protectors.
Use other personal protective equipment such as
■
gloves, apron and helmet when necessary.
Never place the tool on the floor or other surfaces
■
while it is running.
Grinding wheels continue to rotate after the tool is
■
switched off.
Never touch the wheel or place it on the floor or other
■
surfaces while it is rotating.
The flange and clamp nut must have same outer
■
diameter.
Do not remove the soft paper in the center of the
■
grinding wheel. (If the paper has been previously
removed, insert some soft paper or rubber between
grinding wheel and flange.)
Use the tool only for approved applications. Never
■
use coolants or water or use the tool as a fixed tool.
Grip the tool securely with both hands while operating.
■
SPECIFICATIONS
Grinding wheel
Voltage*
Input
Spindle thread
No load speed
Overall length
Net weight
* Be sure to check the nameplate on the product,
because the voltage is subject to change depending
on the area in which the product is to be used.
Maximum circumferential speed of grinding wheel:
4,800 m/min.
Example of calculation:
4,320 = 3.14 x 125 x 11,000 / 1,000
4,320: Circumferential speed of grinding wheel
125: Wheel diameter
11,000: No load speed of grinder
4
H CZ RUS RO
EAG-7511/
EAG-1111
115 mm (4-1/2")
230 V ~ 50 Hz
750 / 1150 W
M14
11,000 min. -1 /
10,000 min. -1
310 mm
2.35 kg
PL SLO HR TR
EAG-7512/
EAG-1112
125 mm (5")
230 V ~ 50 Hz
750 / 1150 W
M14
11,000 min. -1 /
10,000 min. -1
310 mm
2.35 kg