Page 3
Distribution (BSD) license, the GNU General Public License (GPL) as published by the Free Software Foundation (FSF), or the Python Software Foundation (PSF) License Agreement for Python 2.7.3 (Python License). Lantronix grants you no right to receive source code to the Open Source software; however, in some cases, rights and access to source code for certain Open Source software may be available directly from Lantronix’...
Contents 1 About this Guide Purpose and Audience _______________________________________________ 5 Additional Documentation ____________________________________________ 5 2 E220 Series Compatible Models 3 Product Features General Specification ________________________________________________ 7 Power Consumption (mA) ____________________________________________ 7 LAN Panel Details __________________________________________________ 8 3.3.1 LAN Panel I/O Connector ________________________________________ 9...
About this Guide Purpose and Audience This guide provides the information needed to install the Lantronix E220 series cellular router. It covers hardware features, installation instructions, network IP configuration information, and compliance statements. This document does not cover how to configure your E220 series cellular router's software.
85mA 86mA Fi ,GPS on & Cellular 900@33dBm WAN,LAN,RS485 connected & Wi- 310mA 243mA 120mA 75mA 76mA Fi ,GPS on & Cellular 1800@30dBm Table 3-2: Power Consumption (mA) LAN Panel Details Figure 3-1: Router LAN Panel E220 Series User Guide...
A&Y: DATA + B&Z: DATA – • G: Common Ground • DIO ports configurable as input or output, 20 AWG (recommended). • Input detection: 5V, max. 48V • Output: Open collector, max. current 200mA Ground for both DIOs E220 Series User Guide...
Supports PoE (Power over Ethernet). PoE wired Ethernet LANS allow the electrical current necessary for the operation to be carried by the data cable rather than carried by power cords, thus removing the need for an external power supply. E220 Series User Guide...
Weak signal (CSQ > 6 to 12) Amber ON Power Power off Green ON Power on Alert No alert, device is running smoothly Red Flashing Cellular Module reboot, Linux Kernel booting Red ON Hardware fault Table 3-3: LED States E220 Series User Guide...
DIN rail clip • Accessories Lantronix accessories for use with the E220 series router are listed in the following table according to part number and application. Lantronix accessories are available individually or as accessory bundles. To order Lantronix accessories, go to https://www.lantronix.com/about-us/contact/.
Web browser such as Internet Explorer 10+ or Google Chrome 30+, Mozilla Firefox 20+ or Apple Safari 4+ to access the Lantronix Web Admin Console DHCP client enabled on the computer to obtain a valid IP Address from the router.
4. Connect the router to a computer. 5. Run Quick Setup to configure network settings . 4.5.1 Insert the SIM Card Insert the SIM card in the router as shown below. Figure 4-1: Inserting the SIM Card in the Router E220 Series User Guide...
Table 4-2: E220 Series Main and Auxiliary Antennas To connect the Wi-Fi/cellular/GPS antenna: 1. Connect the cellular antenna to the main connector of the E220 series device as shown in the figure below. 2. Use your fingers to securely tighten (clockwise direction) the antenna connector to the connector on the base unit.
The power LED will light when power is applied. Figure 4-3: Connecting the AC Power Connector 4.5.3.1 Power over Ethernet An alternate option is to power the Lantronix Router over Ethernet port as the WAN port supports Power over Ethernet (PoE). NOTE: Please refer to the Appendix for Power over Ethernet connections example.
Page 17
4. Next, you are ready to configure the network settings from the Quick Setup page. To connect via Ethernet: 1. Connect an Ethernet cable between the LAN port on the front panel of the router and the Ethernet port on the computer. Figure 4-5: Router to Computer LAN Connection E220 Series User Guide...
Page 18
Page. We recommend that you set a unique, strong password Configuration for Web Admin for the router and store the password in a secure location. 3. Next, you are ready to configure the network settings from the Quick Setup page. E220 Series User Guide...
To skip the Quick Setup and directly configure the network settings including advanced settings, go to the Network tab. For details on software configuration, please refer to the Lantronix ePack User Guide for E210 and E220 Devices.
The wireless access point SSID may be configured in the Web Admin console. Parameter Details Lantronix E21X - for E210 series devices SSID Lantronix E22X - for E220 series devices WPA/WPA2 TKIP Key W1rele$$ Table 4-5: Default Wi-Fi Credentials E220 Series User Guide...
Page 21
LAN (Ethernet) Active DHCP with starting IP address 192.168.1.100 with pool of 100 clients. Cellular No PAP/CHAP authentication Wireless (LAN) Wi-Fi enabled as access point with SSID "Lantronix E21X" or "Lantronix E22X" Table 4-6: Default Interface Configuration E220 Series User Guide...
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : E220 Series User Guide...
Afin d'éviter la possibilité de dépasser les limites d'exposition aux fréquences radio de la ISED CNR-102, la proximité humaine à l'antenne ne doit pas être inférieure à 20 cm (8 pouces) pendant le fonctionnement normal. E220 Series User Guide...
Dipole, Peak Gain < 3.8 dBi @ 2.4 GHz ~ 2.5 GHz • Selection of antenna type: • Using the same dipole antenna type as certified module & Modem for FCC as above or external antenna with length > 20 cm. E220 Series User Guide...
Need help?
Do you have a question about the E220 Series and is the answer not in the manual?
Questions and answers