Related Manuals for Yard force Classic 500
Summary of Contents for Yard force Classic 500
- Page 1 The expert for robots in your home With one click to the online shop myRobotcenter.eu myRobotcenter.co.uk myRobotcenter...
- Page 2 30 cm < 10 cm > 10 cm max. 30 cm 30 cm Classic 500 min. ROBOTIC MOWER ROBOT-TONDEUSE Original Installation Guide Guide d’installation d’origine MÄHROBOTER ROBOTMAAIER 5 cm < Original Installationsanleitung Originele handleiding ROBOSEKACKA ROBOT KOSZĄCY Originální instalační průvodce...
-
Page 3: Table Of Contents
CONTENT Description of product STOP button Charging port Description of the product ..........1 Rear wheel Height adjustment dial Installation ..............2 Control panel USB interface (only for after service centre) Operation ..............10 On/Off switch Front wheel Technical data ..............14 Cutting blade Maintenance and storage ..........15 Troubleshooting ............17 Scope of delivery... -
Page 4: Installation
Installation Installation Guide This chapter explains how to install the Robotic Mower. Please read this completely before you start the installation. Introduction We recommend creating a drawing of your lawn, including all obstacles and how these should be protected. This makes it easier to find a good position for the docking station and how to correctly place the boundary wire around your garden perimeter protecting bushes, flower beds etc. - Page 5 > +/- 5° > +/- 5° Uneven lawn surfaces Uneven lawn areas may cause the blades to touch the ground. We recommend leveling the lawn If your lawn has a soft or uneven surface, we recommend fortifying the area around the docking before using your Robotic Mower or excluding uneven areas with the boundary wire.
- Page 6 correct distance from lawn edges (30 cm) and obstacles. Ponds and Pools While the Robotic Mower is protected against rain and spray water, being submerged is likely to cause severe damage to the electronic parts. Flowerbeds Therefore, it is imperative to exclude any pools from the cutting area. For added safety, we Use the boundary wire to exclude any flowerbeds from the cutting area.
- Page 7 Insert the mains plug into a properly installed socket. Once the blue LED confirms all is OK, test Signal selection the Robotic Mower's function. Check the LED regularly to ensure fixing the boundary wire has not Note: the default signal is S1, no need to change the signal when there isn’t a influence signal affected the connection and signal shows S1 on the charging satation.
-
Page 8: Operation
Operation button: Operation Home button: First press the Home button and the press the OK button, Robotic Control panel Mower will return to docking station. Start button: First press the Start button and then press the OK button, Robotic Mower will start to work. OK button Lock/Unlock button: Indicator will show when pressed and will lock the control panel. - Page 9 for example: Cutting height adjustment if now is 08:25, please press , and then you would hear a beep. The cutting height can be adjusted by rotating the height adjustment dial located on the top if now is 09:45, please press , and then you would hear a beep.
-
Page 10: Technical Data
Maintenance and storage Maintenance work that has not been described in these instructions must be carried out by a servicing agency authorised by the manufacturer. Only use original parts. Model Classic 500 Max cutting area 500 m Maintenance Battery pack 28 V/ 2000 mAh Check and clean your Robotic Mower regularly and replace worn parts if necessary. -
Page 11: Troubleshooting
Cleaning the underside Troubleshooting Ensure the main power switch is in OFF position. Wearing protective gloves, turn the Robotic Mower onto its side to expose its underside. Clean the blade disc and frame using a soft brush or damp cloth. Rotate the blade disc to make sure that it can move freely, check that the blades can Robotic Mower cannot dock with docking station turn on their pivots and that there is no grass is obstructing them. - Page 12 Charging trouble shooting Problem Possible cause Corrective action Power cable runs parallel/close to Reposition of boundary wire wire Problem Possible cause Corrective action Front wheel is stuck Clean front wheel area Incorrect wire connection Check wire connections "F and B" Signal interfere with robot in Change to alternative boundary No light on charge base...