Related Manuals for wallas 4430
Summary of Contents for wallas 4430
- Page 1 6 0 4 3 9 8 .a i 1 3 .1 1 .2 0 1 1 1 3 :3 8 :1 9 4430 Remote Control System Installation, operation and service instructions...
-
Page 2: Table Of Contents
User settings Starting and stopping the heater Adjusting heater temperature Remote control by text messages Controls Control commands “W” – Wallas heater control Other commands “S” status Connections for a Wallas heater Frequently Asked Questions Resetting the factory settings (Reset) -
Page 3: Technical Information
• Observe the installation instructions. • Only use accessories, which have been recommended by Wallas-Marin Oy. • Do not open the unit or try to repair it when any malfunction occurs. All repairs must be performed by an authorised service provider. Additional information is available from the equipment dealer. -
Page 4: Introduction
Technical information Introduction The remote starter 4430 is intended for communicating data through a GPRS network. The unit is intended for remote controlling of heating devices. The unit can be used for starting and stopping the heater, for adjusting thermostat settings (temperature), and for monitoring accumulator voltage and the temperature of the premises being heated. -
Page 5: Quick Guide
8. Ensure that the green LED light starts flashing with 7 sec intervals 9. Register as a user on the web page remote.wallas.fi by using the instructions on the screen 10. Save the control page as a bookmark (ask to confirm your... -
Page 6: Installation
If you use prepaid SIM cards do not forget to reload them, when the balance is about to run out. 4430 does not function properly if the SIM card is not used cor- rectly. Prepare the SIM card 4430 requires the SIM card’s PIN code request to be OFF. -
Page 7: Installing The Sim Card
4430 Installation Installing the SIM card 1. Make sure that 4430 has not been connected to the operating switch through a cable. 2. Place the card in the position shown on the figure below. GSM aerial interface 3. Push the SIM card into the card slot. A click indicates that the card has been locked in place. -
Page 8: Connecting Of Heaters 1800 T And 2400 T
With the heaters 1800 t and 2400 t the operating switch turns on 8V voltage, which runs the 4430 unit, but the voltage reading on the display is incorrect (8V). It is ad- visable to take the power for these units directly from the accumulator via a sepa- rate fuse, in which case the reading on the display will be correct. -
Page 9: Relays
A Wallas heater functions as a power source in the following equipment 22 Dt, 30 Dt, 40 Dt, 26CC and 40CC. When heaters 1800 t and 2400 t, are used, it is advisable to connect the 4430 unit directly to the same 12V accumulator, which is used by the heater. -
Page 10: Preparing For Start-Up
If necessary remove the SIM card from the unit to prevent excessively high charges. If you intend to stay abroad for a long time, it is advisable to pur- chase a SIM card of a local operator, if you intend to use the 4430 remote starter. D10241... -
Page 11: Operation
Two units cannot be registered with one and the same e-mail address. 6. You may uncheck the box ”I want to be involved in the development of Wallas Remote Control and get information about new Wallas innovations” if you do not wish to receive any e-mails from Wallas-Marin Oy. - Page 12 Operation 8. Enter the password received by e-mail here. 9. Enter your new password. 10. Repeat your new password here again. 11. To log in, click [Login to the panel]. john. smith@ wallas.com john.smith@ wallas.com D30071 490538 - 36 -...
-
Page 13: Settings
2. Select your country from the drop-down menu 3. Select from the drop-down menu the operator [Operator] whose SIM card you have got for your 4430. The accepted/ tested operators for the country selected in the previous menu [Country] are displayed in the drop-down menu; choose your own from the options provided. - Page 14 4430 Operation Equipment validation takes a couple of minutes; an acceptance message will be sent to your e-mail, and a green symbol is displayed on the screen; furthermore, the IMEI code of the registered equipment is displayed on the settings page.
- Page 15 If the validation was not successful, a red symbol is displayed on the screen. Check whether you have entered the correct SIM card number, telephone number, and have selected the correct operator, also ensure that the 4430 unit has been connected and a green LED is flashing with an interval of 7 seconds. After verification click the [Update heater setting] button again to configure the equipment.
-
Page 16: Panel Settings
4430 Operation Panel settings On the Panel settings tab you can practice/ display the functioning of the control panel in the test mode by checking the box [Enable test mode] and pressing [Save settings]. In the test mode commands are not sent to the actual device, but instead the func- tions of the unit are displayed in an accelerated cycle. -
Page 17: User Settings
4430 Operation User settings The User settings tab gives you access to modifying user data. • Change the first name • Change the surname • Change the e-mail address (two units cannot be registered with one and the same e-mail address). To change the e-mail address it is first necessary to de- lete the account by pressing [Delete account]; after this you have to complete the entire registration process once again. -
Page 18: Use
– Stopping • during the cooling process – Cooling • if the remote control 4430 is not connected to the Wallas server – 4430 Discon- nected • if there are problems with connecting to the Wallas heater – Heater discon- nected •... -
Page 19: Starting And Stopping The Heater
4430 Operation Starting and stopping the heater During the heater starting or stopping process a dialog box appears where you can confirm the selection [YES] [NO]. Furthermore, it also contains a notice, warn- ing that in the case there is a closable exhaust lead-through it is open before the heater is started. -
Page 20: Remote Control By Text Messages
Operation Remote control by text messages The 4430 unit can be controlled remotely by sending text messages to the unit. This can be done by a normal GSM phone. The unit has a number of commands for guiding the process. Each command is dif- ferent and contains a letter, which assigns a property to the text message. -
Page 21: Other Commands
The LED colour is red: • Wait for 2 – 3 seconds for the unit to automatically restart. • If it stays on, try to restart the 4430 unit by disconnecting the power source for 10 seconds. • Please contact the equipment dealer. -
Page 22: Resetting The Factory Settings (Reset)
4430 Operation Resetting the factory settings (Reset) It is possible to restore the factory settings. Proceed as follows: • Disconnect the power source. • Press the button “RELAY1” and keep it down. • Connect the unit to the power source and keep the button down for at least 10 seconds. -
Page 23: Maintenance
Waste Electrical and Electronic Equipment The waste electrical and electronic equipment (WEEE) symbol The 4430 unit is covered by WEEE. The EU Waste Electrical and Electronic Equip- ment Directive (the WEEE directive) regulates matters concerning electrical and electronic equipment waste. It lays down the objectives for collection, recycling and recovery of various electronic equipment. -
Page 24: Disclaimer
Wallas-Marin Oy, or its local representative be liable for any direct, indirect, accidental or incidental losses stemming from the use of or inability to use the 4430 unit, even if a notice had been given of such possible loss. Wallas-Marin Oy, or its local representatives are not responsible for any expenses, lost profit, lost data or claims of third parties, which are caused by the use of or inability to use the 4430 unit. - Page 25 Wallas-Marin Oy Kärrykatu 4 Oikeudet muutoksiin pidätetään. 20780 Kaarina Finland We reserve the right to changes. Vi behåller rätten att göra ändringar. www.wallas.com Vi reserverer oss retten til endringer. 490538 D90050-8...