Advertisement
The devices should be transported packaged, in containers, closed railway cars, heated and air-
tight compartments of aircraft and holds and by trucks with rain and snow protection for any
distances at temperatures from -50°C to +50°C and relative humidity of 100% at 25°C.
Average service life is 5 years min.
12. Disposal
At the end of the service life the device is subject to disposal. The device does not pose a hazard
to human health and environment. The device does not contain any non-ferrous and precious
metals.
13. Manufacturer's warranty
Guaranteed storage life is 6 months from the manufacturing date (the last 6 figures in the
product serial number, for example: 191117 – November 19, 2017).
Guarantee service life is 24 months from the date of sale.
With the note of sale absent – from the manufacturing date.
Warranty obligations cease in case of non-observance of operating conditions established by
the manufacturer and mechanical damage during operation. Warranty obligations do not cover
the case of failure to present the device passport.
14. Completeness
Executive device Radio 8113 IP65
Passport
Individual packing
15. Acceptance certificate
Executive device Radio 8113 IP65 (see serial number on the first page) is manufactured in
conformance with RB TR 100376351.002-2003 and essential requirements of technological
regulations, is approved by QCD and is classified as fit for operation.
16. Potential problems
Problem
Probable reason
a) there is no voltage;
The device does not
b) the wires in terminals 1 and 2
operate
are not clamped well.
The curtain moves in an
The drive wires are connected
opposite direction when it
incorrectly.
is
controlled
by
the
remote control button of
definite command.
a) the jumper between terminals
The
device
operates,
indicator blinks red or
6 and 7 is not installed;
b) the jumper between terminals
green but the voltage is
not supplied on drive.
6 and 7 is not clamped well.
a) latching switch is connected,
The device is not entered
in the programming mode
and the button of one of
directions is pressed.
by
programming button.
The drive is turned on for
a short time, roller shutter
twitches and stops.
The
controlled using remote
control and key switch,
red visual indicator blinks
permanently.
1 pc
1 pc
1 pc
Fault elimination
a) apply the voltage supply
Manufacturer:
at terminals 1 and 2.
Nero Electronics LLC
b) clamp the wires in the
Belarus, 223016, FEZ Minsk, Minsk district,
terminals 1 and 2.
Novy Dvor rural council, 74
To change the drive wires
tel./fax: (+375 17) 388-53-00,
connected to the terminals
info@neroelectronics.by,
4 and 5.
www.neroelectronics.by
Representative office in Belarus:
a)
install
Sketch LLC
the
jumper
220073, Minsk, 2b Skryganova str,
between terminals 6 and 7;
office 306
b)
clamp
the
jumper
tel./fax: (+375 17) 317-02-32,
between terminals 6 and 7.
marketing@sketch.by
change
a)
the
latching
switch
on
the
switch
without fixation;
pressing
the
b) switch cable is out of service;
c) the switch is out of service
a) the short command mode is
installed;
b) a short command time is
installed,
which
insufficient for the full closing of
roller shutter.
a) incorrect operation mode of
device
is
not
safety inputs is installed;
b) there is an obstacle in area of
connected safety sensor;
c) cable leading to the safety
sensor is impaired.
Representative offices in Russia:
SketchNerogroup LLC
119361, Moscow, 15 Bolshaya Ochakovskaya Str.,
building 1
tel./ fax: (+7 495) 430-79-60, (+7 495) 735-64-47,
(+7 495) 735-66-58,
Nero SPb LLC
136070, St. Petersburg, 14 Komsomol Str., building 2
tel.: (+7 812) 987-51-56, (+7 981) 757-90-45,
nero-spb@neroelectronics.by
Representative office in Ukraine:
Umnyye resheniya LLC
03138, Kiev, Smolnaya Str., 9B
tel./fax: (+38 067) 679-51-22, (+38 044) 500-18-55,
o.ladyga@neroelectronics.by
b) check/change cable;
c) check/change switch.
a) install the necessary
mode;
b) install the necessary
is
not
command time or reset to
factory setting.
a) install the mode of safety
inputs in accordance with
the sensor or reset to
factory setting.
b) remove an obstacle in
area of sensor;
c) check/change the cable.
Made in the Republic of Belarus
info@nerosk.ru
Advertisement
