CaryMart S1FC-DC06 Manual

RF Wireless Remote Control Radio Controller / Transmitter & Receiver

Package Include:

1 x Receiver: S1FC-DC06 / S1FC-DC09 / S1FC-DC12 / S1FC-DC24 (Two Control Modes)
1 x Transmitter: CV-4-2
1 x User manual

Feature:

Wireless control, easy to install
Control motors of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors or other appliances and mechanicals.
You can rotate the motor in the positive or reversal direction with the transmitter (remote control) from any place within a reliable distance; the
wireless signal can pass through walls, floors and doors.
With characteristics of reverse power protection and over current protection
Audible / visual indication
Use microcontroller model of EM78P156, an 8-bit microprocessor designed and developed with low-power and high-speed CMOS technology.
Use ULN2003 to drive relay, with strong anti-interference.
Reliable control: The transmitter (Encoding) and the receiver (Decoding) use an 8-bit code.
One / several transmitters can control one/ several receivers simultaneously.
If you use two or more receivers in the same place, you can set them with different codes.
Transmitting Frequency: 315MHz / 433MHz

Receiver:

Model No: S1FC-DC06 / S1FC-DC09 / S1FC-DC12 / S1FC-DC24
Control Mode: Momentary, Latching
Coding Type: Fixed code
Coding Setting: By learning
Power Supply (Operating Voltage): DC6V (S1FC-DC06), DC9V±1V (S1FC-DC09), DC12V±1V (S1FC-DC12), DC24V±1V (S1FC-DC24)
PCB Size: 94mm x 56mm x 24mm
Case Size: 100mm x 60.5mm x 30mm
Maximum Current: 10A

Transmitter:

Model No.: CV-4-2
Channel: 4 CH
Remote Control Distance: 500m / 1500ft (theoretically)
Encode: Fixed code by soldering
Unit Size: 108mm x 50mm x 18mm
Power Supply: 1 x 23A -12V battery (included, can be used for 12 months)

Usage:

Connect power line to terminals "+" and "－". Connect DC motor to terminals "UP" and "DOWN". You can exchange "UP" and "DOWN" lines of the
motor to change rotating direction of the motor.
Set Momentary control mode: Do not connect Jumper.
Press and hold button ▲ on remote or receiver: Terminals UP and DOWN output ＋ DC (UP: ＋, DOWN: －), motor rotates continuously in
positive direction.
Release button ▲ on remote or receiver: Stop the motor.
Press and hold button ▼ on remote or receiver: Terminals UP and DOWN output － DC (UP: －, DOWN: ＋), motor rotates continuously in
reversal direction.
Release button ▼ on remote or receiver: Stop the motor.
Set Latching control mode: connect the Jumper.
Press button ▲ on remote or receiver: Terminals UP and DOWN output ＋ DC (1: ＋, 2: －), motor rotates continuously in positive direction.
Press ■ on remote or receiver: Stop the motor.
Press button ▼ on remote or receiver: Terminals UP and DOWN output － DC (1: －, 2: ＋), motor rotates continuously in reversal direction.
Press button ■ on remote or receiver: Stop the motor.
We have learned remote control to the receiver. If you don't want the receiver to work with the remote control, you can delete all codes of remote
controls, which are stored in the receiver.
Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored
codes have been deleted successfully.

Learning the button of remote control:

1) Press the button of receiver; signal LED on the receiver keeps shining. The receiver enters into status of LEARNING.
2) Press any one button on remote control. If signal LED flashes quickly 15 times and turns off, it means learning is successful.
SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: sale@carymart.com