Advertisement
[
ES995 Specifications
Elements
Two fixed-charge
back plate
permanently
polarized condensers
Polar Pattern
Cardioid
Frequency Response
90–15,000 Hz
Low-frequency Roll-off
Fixed 120 Hz,
12 dB/octave
Open Circuit Sensitivity –41 dB (8.9 mV)
re 1V at 1 Pa
Impedance
250 ohms
Maximum Input Sound
138 dB SPL, 1 kHz at
Level
1% T.H.D.
Dynamic Range
109 dB, 1 kHz at
(Typical)
Max SPL
Signal-to-noise Ratio
1
65 dB, 1 kHz at 1 Pa
Switches
SW1: Normal/–15
(on circuit board)
dB; SW2: Mute/
Toggle / Talk;
SW3: Off/On
Phantom Power
11–52V DC, 3 mA
Requirements
typical
Weight
3.31 lb (1.5 kg)
[
Visit our Web site at www.audio-technica.com
Audio-Technica microphones and accessories purchased in the U.S.A. are warranted for one year from date of
purchase by Audio-Technica U.S., Inc. (A.T.U.S.) to be free of defects in materials and workmanship. In event of such
defect, product will be repaired promptly without charge or, at our option, replaced with a new product of equal or
superior value if delivered to A.T.U.S. or an Authorized Service Center, prepaid, together with the sales slip or other
proof of purchase date. Prior approval from A.T.U.S. is required for return. This warranty excludes defects due
to normal wear, abuse, shipping damage, or failure to use product in accordance with instructions. This warranty
is void in the event of unauthorized repair or modification.
For return approval and shipping information, contact the Service Department, Audio-Technica U.S., Inc., 1221
Commerce Drive, Stow, Ohio 44224.
Except to the extent precluded by applicable state law, A.T.U.S. will have no liability for any consequential,
incidental, or special damages; any warranty of merchantability or fitness for particular purpose expires
when this warranty expires.
This warranty gives you specific legal rights, and you may have other rights, which vary from state to state.
Outside the U.S.A., please contact your local dealer for warranty details.
Form No. 0309-2130-00
P51565 © 2003 Audio-Technica U.S., Inc. Printed in U.S.A.
Dimensions
Output Connector
Cable
*
Accessory Furnished
Optional
Interchangeable
*
Elements
†
In the interest of standards development, A.T.U.S. offers full details
on its test methods to other industry professionals on request.
*
1 Pascal = 10 dynes/cm
1
Typical, A-weighted, using Audio Precision System One.
Specifications are subject to change without notice.
[
]
Dimensions
One-Year Limited Warranty
]
†
19.51" (495.6 mm)
maximum length,
1.51" (38.4 mm)
maximum head
diameter
Integral 6-pin
Neutrik XLRM
30' (9.1 m)
6-conductor shielded
"Y" cable–6-pin
XLRF to two 3-pin
XLRM
Switch
cover label
ESE-H hypercardioid
(100°)
ESE-O
omnidirectional
(360°)
2
= 10 microbars = 94 dB SPL
]
[
Polar Pattern
0
330
30
300
270
240
210
150
180
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz
[
Frequency Response
50
100
200
500
1k
2k
Frequency in Hertz
LEGEND
12" or more on axis
[
Architects and
Engineers
Specifications
The microphone shall be a dual-element,
fixed-charge condenser with a frequency
response of 90 Hz to 15,000 Hz and a
cardioid polar pattern with uniform 120°
angle of acceptance. It shall contain two
shock-mounted
cardioid
elements
isolated grounds. It shall operate from an
external 11V to 52V DC phantom power
source. It shall be capable of handling sound
input levels up to 138 dB with a dynamic range
of 109 dB. It shall have a fixed low-frequency
roll-off of 120 Hz, 12 dB/octave. Output shall
be low-impedance balanced (250 ohms).
The microphone shall be a small-diameter,
rigid-pipe design with pivoting ball-in-socket
arrangement and lighted mute switch. The
microphone shall have an integral dual power
module with 6-pin XLRM-type connector for
use with the included 30' splitter cable. The
cable shall connect to the microphone by a
6-pin XLRF-type connector and shall terminate
in two 3-pin XLRM-type connectors. The
power module shall include a 15 dB pad switch,
three-mode mute switch, and defeat switch.
The microphone's overall length shall be
19.51" (495.6 mm). Head diameter shall be
1.51" (38.4 mm). The microphone assembly
(less cable) shall weigh 3.31 lb (1.5 kg). Finish
shall be low-reflectance black.
The Audio-Technica ES995 is specified.
Audio-Technica U.S., Inc.
1221 Commerce Drive, Stow, Ohio 44224
]
60
90
120
]
10 dB
5k
10k
20k
[
with
Advertisement
