Navigating The File Menu; Open Environment; Save Environment; Receiver Configuration - Audio Technica Artist Elite 5000 Installation And Operation Manual

Navigating the File Menu

Open Environment

Use the Open Environment command to open a saved
environment (collection of settings for a particular set of
receivers working as a system).
To open a saved environment:
1. Click on File > Open Environment .
2. In the Open Environment input popup, select the name
of the environment to open.
3. Click OK .

Save Environment

Use the Save Environment command to save the current
environment.
To save an environment:
1. Click on File > Save Environment .
2. In the Save Environment input popup, either choose an
already-entered environment name from the dropdown
menu (this will save the current environment over the
previous file), or select New Environment to enter a new
name, and click OK .
3. If you chose to enter a new environment name, type it in
the Environment Name popup and click OK , or click Cancel
to return without saving the environment.
Note: Saving an environment saves only the receiver
settings , not the receiver configuration. In other words,
applying a saved setting will adjust settings on enabled
receivers that are part of that environment, but it will not
enable disabled receivers that are also in the environment,
and it will not disable enabled receivers that are not part of
the environment.

Receiver Configuration

Use the Receiver Configuration command to open the
Receiver Display Setup window, where you can change the
order of display of receivers in the system, or enable/disable
receivers.
When the software first boots up, it looks for receivers within
its network. Any receivers it finds appear in the Network
Configuration window as Discovered . Any receiver that is
discovered may be enabled in the Receiver Configuration
window, unless it is in use by another computer.
Note: A receiver may be enabled on only one computer at a
time. Other computers on the network will be able to view
the receiver's IP address but will not be able to enable it.

To change the order of display of a receiver:

1. Click on File > Receiver Configuration .
2. In the Receiver Display Setup window, click on the receiver
to select it.
3. Click on Move Up or Move Down to change its display
order.
4. Click OK to accept the changes and return to the Main
window, or Cancel to return to the Main window without
applying the changes.
Installing and Using the Software
(Continued)

To enable or disable a receiver :

1. Click on File > Receiver Configuration .
2. In the Receiver Display Setup window, click on the receiver
to select it.
3. Click on Enable/Disable . (Enable allows you to activate a
discovered receiver; Disable allows you to free up a
discovered receiver so that other users on the network
may access it.) If the unit is enabled, Disable will display
on the button, and vice versa.
4. Click OK to accept the changes and return to the Main
window, or Cancel to return to the Main window without
applying the changes.
5. The system applies your changes and reconnects to the
network.
Note: Disabling either channel of an AEW-R5200 unit
disables the entire receiver (channels 1 and 2), thus freeing
an Ethernet port. Any AEW-R4100 units linked to the
AEW-R5200 are also disabled.
Caution: Any time you make changes to the
Receiver Configuration, the software performs a
Reconnect to Network . All receivers are muted
during this process. Therefore, do not make
changes to Receiver Configuration at any time
when system muting would be undesirable!

Network Configuration

The Network Configuration window shows information such
as IP address, MAC address, Firmware version (of the receiver
unit), Enabled status (enabled or disabled), and Discovered
status (detected or added) for all receivers in the system.
Until receivers have familiar frequency settings or receiver
names, you may not be able to distinguish them, unless you
know which receivers are using which IP addresses.

To add a remote receiver by entering its IP address:

From the Network Configuration window, click Add ... and
enter the IP address in the Input popup. (See page 10 for an
application of this feature.)
Caution: Any time you make changes to the
Network Configuration, the software performs a
Reconnect to Network . All receivers are muted
during this process. Therefore, do not make
changes to Network Configuration at any time
when system muting would be undesirable!

Exit

Use the Exit command to close all windows and exit the
software.
13