Sapphire Audio HOSS 700 Owner's Manual

Sapphire Audio HOSS 700 Owner's Manual

Rotary cleaning tool
Hide thumbs Also See for HOSS 700:

Advertisement

Quick Links

HOSS 700 Rotary Cleaning Tool
Sapphire Scientific • Sales: 866-445-3030 • Technical Support: 866-445-3030.
Congratulations on your purchase of a HOSS 700 Rotary Cleaning Tool from Sap-
phire! With a durable design and innovative cleaning features, the HOSS 700 makes
carpet cleaning easier, more effective and more profitable.
R E A D A N D S A V E T H E S E I N S T R U C T I O N S
SAFETY INSTRUCTIONS
WARNING
WARNING! Electric shock hazard, rotating parts, hot
surface hazards. Unplug unit before opening cover
for cleaning or servicing. Unit must be properly
grounded.
• Inspect the power cord before use. If cord is dam-
aged, do not use. Always grasp the plug (not the
cord) to unplug.
• The unit must be operated on a 110V/60Hz circuit.
• Keep motor and wiring dry.
• Do not operate in standing water
49-075D 2011-09 Warranty 49-071
Owner's Manual
Patents pending
• Do not operate in rain or snow. If electrical compo-
• Do not attempt to repair the unit. For technical sup-
NOTICE: Protect from freezing during storage and
transport. Damage caused by freezing is not covered by
the product warranty.
INTRODUCTION
The HOSS 700 Rotary Cleaning Tool greatly improves
cleaning performance and efficiency on a wide variety of
carpet types.
• High-flow solution orifices and high efficiency va-
• ½ HP 1725 RPM motor
• Sealed low-maintenance gear box
• 6 in. non-scuffing wheels for easy transport
• Fully adjustable handle for maximum operator com-
1
nents become wet, allow them to dry before using.
port, call Sapphire at 866-445-3030.
cuum plates
fort and control
Sapphire Scientific

Advertisement

Table of Contents
loading

Summary of Contents for Sapphire Audio HOSS 700

  • Page 1 Owner’s Manual Sapphire Scientific • Sales: 866-445-3030 • Technical Support: 866-445-3030. Congratulations on your purchase of a HOSS 700 Rotary Cleaning Tool from Sap- phire! With a durable design and innovative cleaning features, the HOSS 700 makes carpet cleaning easier, more effective and more profitable.
  • Page 2: Parts Identification

    PARTS IDENTIFICATION IMPORTANT: The HOSS 700 is shipped with the handle and electrical cord unat- tached. Attach these items before using. See “Handle Installation Instructions,” p. 4. Figure 1 A. Handles. B. Solution control lever. Squeeze to start solution flow.
  • Page 3 PARTS IDENTIFICATION (cont.) Figure 3 N. Solution orifices (×5). May be removed with a ⅜ in. socket or nut driver for cleaning or replacement. Align rotor with Access Notch P in housing to access each orifice. Q. Vacuum feet Q (×5). May be removed for cleaning or replacement. Fig.
  • Page 4 HOSS 700 Assembly Instructions IMPORTANT! Complete these steps before using the HOSS 700 for the first time. Tools required: • Pliers • Phillips head screwdriver • ¼ in. ratchet • Two 9/16 in. wrenches. 1. Slide the handle brace to the center of the axle and attach E clip A retaining ring to the axle.
  • Page 5 3. Attach handle brace to handle assembly. Place flat washer H and rubber washer G on the threaded shaft of knob F as shown. Insert knob F through slot in han- dle and thread into T-bracket J. 4. Attach the blue solution line K to the top of vacuum inlet cap M.
  • Page 6 5. Place nut, rubber gasket as shown over the end of the power cord. Insert the three wires through the re- tainer ring one at a time, starting with the black wire, then the the white wire, then the green wire. After in- serting the wires, reseat the rubber gasket insider the retainer ring.
  • Page 7: Operation

    Cleaning and Operational Tips 4. Connect to a 115V/15 amp supply power source (Fig. Do not operate the HOSS 700 on dry carpets, as this 1, G), using a suitable extension cord. Cords up to 50 ft. may damage carpet fibers.
  • Page 8: Maintenance

    Check gearbox oil levels. Remove vented gear case MAINTENANCE plug (S). While looking into vent plug hole, tilt unit back onto its wheels to allow rotary head to be turned. Turn WARNING: Electrical shock hazard. Unplug unit be- the head until vent plug hole is aligned with the hole in fore performing any maintenance task.
  • Page 9: Troubleshooting

    800-932-3030. Contact your Sapphire distributor for replacement parts and rebuild kits. WARRANTY HOSS 700 SPECIFICATIONS Warranty information is available from your dealer or at Model HOSS 700 Rotary Cleaning Tool www.sapphirescientific.com. Cleaning width 15 in. | 38 cm diameter head Warranty registration Use weight 68 lbs.
  • Page 10: Parts Diagrams

    PARTS DIAGRAMS Wiring Schematic 49-075D 2011-09 Warranty 49-071 Sapphire Scientific...
  • Page 11 Handle Assembly 49-075D 2011-09 Warranty 49-071 Sapphire Scientific...
  • Page 12 Trigger Valve Assembly 49-075D 2011-09 Warranty 49-071 Sapphire Scientific...
  • Page 13 Drive Head Assembly 49-075D 2011-09 Warranty 49-071 Sapphire Scientific...
  • Page 14 Vacuum Head Assembly 49-075D 2011-09 Warranty 49-071 Sapphire Scientific...
  • Page 15 Vacuum Head Assembly: Tube Length Detail 49-075D 2011-09 Warranty 49-071 Sapphire Scientific...
  • Page 16 PURCHASE Purchase date: ________________________ Serial number: ________________________ Distributor: ________________________ Tel. _________________________ MAINTENANCE D A T E S E R V I C E P E R F O R M E D P E R F O R M E D B Y 49-075D 2011-09 Warranty 49-071 Sapphire Scientific...

Table of Contents