483 x 44 x 158 mm Shipping Dimensions (WxHxD) 550 x 70 x 255 mm Net weight 2.1 kg Shipping weight 3.2 kg Table 1 April 01 , 2021 USER MANUAL FOR AIB-2000 IO (INPUT-OUTPUT) BOX - 4 - User Manual...
FRONT AND REAR PANELS 3 FRONT AND REAR PANELS Figure 2: Front and Rear Panels of AIB-2000 ON-SYNC IN Left+Right XLR. Front XLR - Back RCA NON-SYNC IN switch. MIC IN XLR. Phantom +48V switch. HPF 100 Hz switch. MIC IN gain knob.
ETHERNET/ AES/EBU/ ANALOG OUT CONNECTION 5 ETHERNET/ AES/EBU/ ANALOG OUT CONNECTION Analog outputs ETH In AES/EBU In April 01 , 2021 USER MANUAL FOR AIB-2000 IO (INPUT-OUTPUT) BOX - 7 - User Manual...
CONNECTIONS TO THE MAINS SHALL BE DONE ONLY BY AN ELECTROTECHNICALLY SKILLED PERSON ACCORDING TO THE NATIONAL REQUIREMENTS OF THE COUNTRIES WHERE THE UNIT IS SOLD. April 01 , 2021 USER MANUAL FOR AIB-2000 IO (INPUT-OUTPUT) BOX - 8 - User Manual...
Page 10
PERSONNEL FOLLOWING APPLICABLE SAFETY RULES. DO NOT ALLOW INSTALLING OF THIS UNIT IF INSTALLATION HARDWARE IS BROKEN, BENT, PARTS ARE MISSING OR IS OTHERWISE DAMAGED. April 01 , 2021 USER MANUAL FOR AIB-2000 IO (INPUT-OUTPUT) BOX - 9 - User Manual...
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ▪ Consult the dealer or an experienced radio/TV technician for help. April 01 , 2021 USER MANUAL FOR AIB-2000 IO (INPUT-OUTPUT) BOX - 10 - User Manual...
AIB-2000 with the GDC SR-1000 Media Server and Cinema Sound System. 8.2 Unpacking and Checking for Shipping Damage Your AIB-2000 has been completely tested and inspected before leaving the factory. Carefully inspect the shipping package before opening it and then immediately inspect your new product. If you find any damage notify the shipping company immediately.
9 AIB-2000 CONNECTIONS 9.1 Installation The AIB-2000 is a 1U Rack device and most conveniently installed in the amplifier rack it connects to. NOTE: Instead of connecting the AIB-2000 to the power grid directly, it is recommended to plug the device’s mains connection to a UPS outlet.
7.1 ANALOG button chooses the input from 7.1. INPUT connectors on the back. ▪ AES/EBU button chooses the signal from digital AES/EBU in on the back. April 01 , 2021 USER MANUAL FOR AIB-2000 IO (INPUT-OUTPUT) BOX - 13 - User Manual...
LCR mon LCR mon provides monitoring output which is received from the AES/EBU stream. Please note that the LCR mon output provides a L+C+R summation of the AES inputs to the AIB-2000. H/I and V/I H/I and V/I outputs are extracted from AES/EBU stream and provides for cinema-goers with hearing and vision difficulties.
NOTE: The H/I and V/I outputs are derived from AES/EBU Channels 7 & 8. Please use the H/I and V/I AES outputs from the SR- 1000 when using the ‘GDC Channel Assignment Preset Output Routing’. Please refer to the ‘Audio Processing Settings for SR-1000’ document for more details.
MIC, setting MIC output to CENTER/SIDE SURROUND channels. The AIB-2000 can be controlled from the SR-1000 (with audio processing enabled) by choosing the default AIB-2000 device in the SR-1000 Automation settings. For more details, please refer to the ‘Audio Settings for SR-1000’...
11 AIB-2000 WEB INTERFACE The AIB-2000 provides a user with a web interface to access its controls. AIB-2000 must be connected to a wired or a wireless network via the ETH port. The device used for accessing the web interface must be in the same network as the AIB-2000.
Make sure your computer is in the same network as the AIB-2000 and has the same network mask. Open a web browser and enter the IP of the AIB-2000 in the Address bar. Enter the login credentials and click on the Sign In button.
Default input Microphone [Save] channels. Table 3 Config → IP config The IP config sub-menu allows the user to set network parameters for the AIB-2000. Figure 9: IP config Sr. No. Name Function Description choose between ‘Static IP’ or Allows the user to [IP type:] ‘Receive IP from DHCP server’.
Cancel [Save / Cancel] discard the changes. Table 4 Config → Misc config The Misc config sub-menu allows the user to set the Username and Password for the AIB-2000. Figure 10: Misc config Sr. No. Name Function Description [User name:] Allows the user to change the username.
AIB-2000 WEB INTERFACE Config → Reboot The Reboot sub-menu allows the user to reboot the AIB-2000 by clicking the Reboot Device button. Figure 11: Reboot April 01 , 2021 USER MANUAL FOR AIB-2000 IO (INPUT-OUTPUT) BOX - 21 - User Manual...