Related Manuals for Eastwood 51117
Summary of Contents for Eastwood 51117
- Page 1 ABRASIVE BLASTER ASSEMBLY & OPERATING INSTRUCTIONS Eastwood Item Numbers 51117, 51118, 51119 #51118 100-lb. Blaster #51117 50-lb. Blaster #51119 200-lb. Blaster...
-
Page 2: Safety Information
This Eastwood Abrasive Blasters are specifically designed to quickly and efficiently designed to strip away old paint and coatings, body fillers, accumulated dirt and moderate to major rust leaving a clean, bare metal surface ready for damage repair or painting. - Page 3 “0”, and it has been disconnected from air supply. • Check for damage regularly. If any part of the blaster is damaged or, if in doubt, the part should be replaced. Only qualified persons familiar with high-pressure pneumatic equipment should perform repairs. Consult Eastwood for advice.
-
Page 4: Specifications
(1) Tank Assembly with pre-installed Outlet Manifold, Inlet Hose, Pressure Relief Valve and Fill Cap with Seal Ring (1) Left and Right Handle Bars with Handgrips (Two Pieces in #’s 51117 & 51118, One Piece in #51119) (1) Blast Hood... - Page 5 Assembly Hardware """" 1/4" NPT Quick Fitting Front Cotter Pins Support Leg Axle Wheels Air Inlet Valve Pressure Inlet Manifold/ Gauge Air Inlet Tube Moisture Separator Pipe Thread Tape Assembly Nozzles To order parts and supplies: 800.345.1178 >> eastwood.com...
- Page 6 Filler Cap Air Supply Valve """" Pressure Relief Valve Inlet Manifold Assembly """" Air Inlet Throttling Valve Moisture Trap Abrasive Control Valve Blast Hose and Safety Valve Assembly Eastwood Technical Assistance: 800.544.5118 >> techelp@eastwood.com...
- Page 7 Handle Bar mounting tabs facing upward (Fig B). 3. Place left and right tubular Handle Bars (NOTE: 2 pieces on Item #’s 51117 & 51118. One piece Handle on #51119) over the welded-on Handle Bar mounting tabs. The curved ends with rubber hand grips should point upward and be oriented toward the top of the Tank Assembly (Fig B).
- Page 8 Place a cotter pin through the holes and fold split ends over (Fig E). NOTE: Steps 9-10 are not necessary on the #51117, 50-lb. Blaster. 9. Apply Teflon Tape (included) to the Air Inlet Tube Threads by wrapping it in clockwise direction as viewed from the open FIG.
-
Page 9: Operation
IMPORTANT NOTES Check to make sure the abrasive is dry and clean so that it does not clog the unit. The use of an Eastwood #22022 Blast Media Screen Sifter or a #50417 Abrasive Media Funnel Strainer is highly recommended to help avoid possible media clogging. - Page 10 9. Begin blasting. 10. Drain moisture trap frequently during use. Do not allow moisture to fill more than 1/2 the water trap bowl. Do not leave water standing in moisture trap when done blasting. Eastwood Technical Assistance: 800.544.5118 >> techelp@eastwood.com...
-
Page 11: Nozzle Replacement
(Fig K). 4. Insert the replacement Seal Pad into the recess making sure the metal plate surface is parallel with the Nozzle outlet. Replace the Phillips head screw and nut (Fig K). To order parts and supplies: 800.345.1178 >> eastwood.com... -
Page 12: Maintenance
1. Drain water trap frequently during use. Do not allow moisture to fill more than 1/2 the water trap bowl. Do not leave water standing in water trap when done blasting. 2. Keep your Eastwood Abrasive Blaster clean, and protect it from damage. 3. - Page 13 • Open and remove Inlet Fill Cap. • Invert blaster and shake out contaminated media. • Refill Tank. The use of an Eastwood #22022 Blast Media Screen Sifter or a #50417 Abrasive Media Funnel Strainer is highly recommended to help avoid possible media clogging.
-
Page 14: Warranty
If you have a product that does not work correctly within 30 days of your purchase, it can be returned to The Eastwood Company for credit or replacement. - Page 15 To order parts and supplies: 800.345.1178 >> eastwood.com...
- Page 16 Soda Blasting Retrofit Kit If you have any questions about the use of this product, please contact The Eastwood Technical Assistance Service Department: 800.544.5118 >> email: techelp@eastwood.com PDF version of this manual is available online >> eastwood.com/51116manual The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA US and Canada: 800.345.1178...