Advertisement
Quick Links
Advertisement
Related Manuals for Eastwood CONCOURS LT100
Summary of Contents for Eastwood CONCOURS LT100
- Page 1 Item #15639 CONCOURS LT100 ® HVLP PAINT GUN INSTRUCTIONS...
-
Page 2: Specifications
• Requires 4.5 CFM [120 l/min] @ 30 PSI [2 Bar] • 1/4” male NPT air input threads • M16 x 1.5 NPS paint cup inlet attachment threads • 1.3 mm stainless steel needle/nozzle set installed (others available) Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com... -
Page 3: Safety Information
• Do not allow unprotected persons or pets in the spray area. BURSTING HAZARD! • Do not exceed 60 psi (4.1 bar) of air inlet pressure. Permanent paint gun damage and/or bursting could occur and cause personal injury. To order parts and supplies: 800.343.9353 >> eastwood.com... - Page 4 Smaller I.D. hose and greater length may reduce available CFM and produce unsatis- factory results. • A clean, dry, regulated air supply is required. An Eastwood #31633, Eastwood Air CFS, or equivalent works well. • To avoid pulsation of pressure when the trigger is depressed, an optionally available, remotely mounted, main regulator should be set to approx.
- Page 5 Fluid Control Setting. 3. Remember that a small amount of product wasted at this point can avoid disappointment in your results and the need to re-do your work later. To order parts and supplies: 800.343.9353 >> eastwood.com...
- Page 6 For most painting conditions, a larger, softer fan is desired (FIG 3). Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com...
- Page 7 • Attach Paint Cup, then pour a small amount of a solvent compatible with the paint being used into the Cup, then run solvent through HVLP Gun in a safe area until it flows clear. As an alternative, #12846Z Eastwood Aerosol Injected Gun Cleaner and #16154ZP Eastwood Paint Gun and Equipment Cleaner are excellent for this purpose.
- Page 8 19mm hex of the included FIG. 7 wrench (do not-over tighten). • Replace Air cap by threading Retain- ing Ring onto Gun Body. Make sure the air horns of the Air Cap are oriented properly. Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com...
-
Page 9: Troubleshooting
Speed up gun motion over surface. too slowly over surface Excessive Runs and Sags Excessive fluid Decrease fluid flow by adjusting “fluid” knob. flow Paint mixed too Check paint manufacturer’s reducing/thinning thin instructions. To order parts and supplies: 800.343.9353 >> eastwood.com... - Page 10 Tighten Nozzle and or Air Cap. cap loose. Paint Spray Needle tip or is Sputtering Nozzle seat Replace Needle/Nozzle set. damaged. Gun being Operate gun with tip tilted no more than tipped too far 45º down or up. down. Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com...
- Page 11 Exaggerated Fluid flow “Football” adjusted Decrease fluid flow adjustment on gun. Shaped Spray too high. Pattern Paint mixture Check paint manufacturer’s mix ratio instructions too thick. or thin if possible. To order parts and supplies: 800.343.9353 >> eastwood.com...
-
Page 12: Additional Items
Kresto Cherry Scrubbing Wipes If you have any questions about the use of this product, please contact The Eastwood Technical Assistance Service Department: 800.343.9353 >> email: tech@eastwood.com PDF version of this manual is available at eastwood.com The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA 800.343.9353 eastwood.com...