Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Stark 5030
Summary of Contents for Stark 5030
- Page 1 Original Operating and maintenance manual Road Grader (5030)
-
Page 2: General
For us, the long lifecycle and efficiency of your new equipment is a priority. To keep the road grader in top working condition, read this manual carefully before using the equipment. STARK products are engineered and manufactured in Finland, and each of them is equipped according to the needs of the customer. -
Page 3: Table Of Contents
Table of contents General ..............................2 Read before use ........................... 2 1. DECLARATION OF CONFORMITY ...................... 4 2. PURPOSE OF USE ..........................5 3. SAFETY PRECAUTIONS ........................5 4. IDENTIFICATION INFORMATION AND SPAREPARTS ................ 6 4.1. Identification plate ..........................6 4.2. -
Page 4: Declaration Of Conformity
1. DECLARATION OF CONFORMITY The original manufacturer’s EC declaration of conformity: Generic product name: Road grader Models: TL 7500 Manufacturer: Lametal Ltd Kaskenviertäjäntie 2 73100 LAPINLAHTI, Finland tel. +358 17 731 565 Declares that the above-mentioned equipment meets the provisions of Directive 2006/42/EC on machinery and, where applicable, comply with the standards •... -
Page 5: Purpose Of Use
2. PURPOSE OF USE STARK Road graders are used for grading gravel roads and flat areas and for transferring ice (removal of packed snow). The device can also be used to shape and align fields. 3. SAFETY PRECAUTIONS Make sure you know your equipment before you start using it. Equipment may be operated only by an individual who is thoroughly familiar with its use. -
Page 6: Identification Information And Spareparts
(marked in the identification plate) when you order spare parts. For more information on maintenance and spare parts, please contact the STARK maintenance and spare part services or your retailer. -
Page 7: Main Parts Of The Road Grader
5. MAIN PARTS OF THE ROAD GRADER Picture 2. Main parts of the road grader 1) Frame of the road grader 2) Shaft of the windrow spreader 3) Front wing 4) Middle wing 5) Back wing 6) Windrow spreader 7) Lift arm 8) Box Sivu 7 / 18... -
Page 8: Attaching The Road Grader
6. ATTACHING THE ROAD GRADER When attaching the road grader for the first time, make sure it is compatible with the base machine by following the instructions below. Always check the compatibility when attaching the road grader to a new base machine. Make sure that the base machine allows installation of the road grader. -
Page 9: Operating The Road Grader
7. OPERATING THE ROAD GRADER Before operating the road grader, make sure: the road grader is installed correctly all locking pins are in place hydraulic hoses are connected right and properly hoses are intact there are no oil leaks all functions are working properly learn to operate the road grader in a closed area before actually using the device 7.1. - Page 10 Picture 3. Functions for remote controller and controller box Sivu 10 / 18...
-
Page 11: Adjusting The Blades
7.3. Adjusting the blades Edge of the blade should be 15–45 mm lower than the blade frame. Blades need to be adjusted at the latest when the blade edge is less than 10 mm lower than the blade frame (picture 4). Do not adjust the blades more than 50 mm lower than the blade frame. -
Page 12: Detaching The Road Grader
Picture 7. Turned blade Picture 8. Turned and lowered blade 7.4. Detaching the road grader When you disconnect the blade assembly from the tractor, lower the assembly on a flat surface and rest it on the blades. Rest the blades on top of strong support brackets. When transferring road grader for long distances, windrow spreader must be secured to upwards stance with e. -
Page 13: Maintaining The Road Grader
8. MAINTAINING THE ROAD GRADER 8.1. General safety precautions for the use and maintenance Comply with the applicable laws and regulations and the instructions in this manual Never go under the road grader if it is not supported Always put on the base machine’s parking brake before any servicing on the road grader. Use only tools which are in good condition. -
Page 14: Daily Maintenance
8.4. Daily maintenance It is important to perform a daily visual inspection of the road grader for early detection of possible faults and to prevent further damage. Inspect the following items on the road grader daily: Hydraulic hoses and components for possible leaks General mechanical condition 8.5. -
Page 15: Lubrication Points
8.7. Lubrication points 1) Pegs of the lift arm 2) Hydraulic cylinder of the windrow spreader’s shaft 3) Hydraulic cylinder of the wheel rack 4) Pegs of the wheel rack 5) Wheel’s brake pole 6) Fastener peg of the windrow spreader 7) Hydraulic cylinder of the windrow spreader’s support wheel 8) Pole of the extension blade 9) Fastener peg of the windrow spreader... - Page 16 Picture 11. Lubrication points Sivu 16 / 18...
-
Page 17: Hydraulics
9. HYDRAULICS The road grader is attached to the base machine with 10-hose hydraulics (figure 1). The system has been tested and adjusted by the manufacturer. Any alterations or modifications to the hydraulic system are on the sole responsibility of the client. -
Page 18: Warranty Policy
3. Warranty period STARK warranty covers a period of one (1) year. If need be, the client and the manufacturer make separate agreements on warranty concerning repairs and spare parts used in repairs. 4. Repairs during the warranty period Repairs during the warranty period are carried out free of charge within the normal working hours by the manufacturer repair and maintenance services or by a repair service provider accredited by the manufacturer.
Need help?
Do you have a question about the 5030 and is the answer not in the manual?
Questions and answers