Advertisement
Quick Links
Installation Note
Agilent Technologies PSG Series Signal Generators E8267C
Upgrade Kit for Option 602 (Digital Bus Baseband
Generator with 64 Msample Memory)
Kit Part Number E8267CK-602
Part Number E8251-90275
Printed in USA September 2009
Supersedes: October 2003
Advertisement
Related Manuals for Agilent Technologies PSG Series
Summary of Contents for Agilent Technologies PSG Series
- Page 1 Installation Note Agilent Technologies PSG Series Signal Generators E8267C Upgrade Kit for Option 602 (Digital Bus Baseband Generator with 64 Msample Memory) Kit Part Number E8267CK-602 Part Number E8251-90275 Printed in USA September 2009 Supersedes: October 2003...
- Page 2 The information contained in this document is subject to change without notice. Agilent Technologies makes no warranty of any kind with regard to this material, including but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Agilent Technologies shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
- Page 3 To Be Performed By: ..... . (X) Agilent Technologies Service Center (X) Personnel Qualified by Agilent Technologies (X) Customer Estimated Installation Time: ....
-
Page 4: Installation Kit Parts List
Installation Kit Parts List Item Quantity Description Part Number Installation Note E8251-90275 PSG Firmware Upgrade Kit E4400-60597 A17 Baseband Generator Interface E4400-60655 W90 Digital Bus Cable 8121-0690 W64 AUX I/O Cable 8121-0920 W65 BNC Cable (Baseband Generator Reference IN) 8121-0901 Hex Nut 15/21-32 (AUX I/O) 2950-0035 Washer .4721D (BNC) - Page 5 Safety Considerations Before you disassemble the signal generator, turn the power switch off WARNING and unplug the power cord. Failure to unplug the signal generator can result in personal injury. Electrostatic discharge (ESD) can damage or destroy electronic components. All CAUTION work on electronic assemblies should be performed at a static-safe workstation.
- Page 6 Install New Firmware 1. Use the installation note, provided in the PSG firmware upgrade kit, E4400-60597, to install new firmware. 2. Perform the verification procedure described in the firmware upgrade installation note. Initialize the Signal Generator Memory If you have access to a LAN, 1.
- Page 7 Remove the Outer and Inner Signal Generator Covers Remove the Outer Cover Refer to Figure 1. Disconnect the power cord. 2. Using a T-20 driver, loosen the two screws (1) and remove the strap handle (2). 3. Using a T-15 driver, remove the center screws (3) on the four rear-panel feet (4). 4.
- Page 8 Figure 1 Outer Cover Removal...
- Page 9 Figure 2 Inner Top Cover Removal Replace the A17 Digital Bus Baseband Generator Interface Board Refer to Figure 1. Disconnect the W64 ribbon cable from A17P2. 2. Using the needle-nose pliers, disconnect the W68 wire cable from A17P4. 3. Using the 9/16” nut driver, remove the hex-nuts and washers securing the four BNC connectors (1) on the rear panel.
- Page 10 Figure 3 A17 Baseband Generator Interface Board W64/A17P2 W68/A17P4...
- Page 11 Replace the A14 Digital Bus Baseband Generator Board NOTE If this upgrade kit is being used for the original installation of an A14 Digital Bus Baseband Generator board, skip steps 1 thru 4. Refer to Figure 1. Using the needle-nose pliers, disconnect the W65 flexible cable from A14J800. 2.
- Page 12 Figure 4 A14 Internal Baseband Generator Board W64/A14J13 W65/A14J800 W90/A14J21...
- Page 13 Install the Digital Bus Cable 1. Refer to Figure 5. Connect the loose end of W90 to A17P1 on the A17 Baseband Generator Interface Board. Make sure the angled side of the cable connector on W90 is facing up. CAUTION Failure to do so could result in damage to the A17 Rear Panel Interface Board connector.
- Page 14 Verify Proper Installation of Option 602 1. Turn the signal generator on. 2. Check that Option 602 is installed by pressing > > Utility Instrument Info/Help Mode Options Info 3. Perform the “Checking Signal Generator Functionality” procedure, as described on page 4.