Advertisement
0
10
20
80
70
INDUSTRIAL AND MASTERSTREAM 1000, 150 PSI (10 BAR, 1000 KPA )
60
50
40
30
20
10
0
0
20
40
60
FIG 5 - Industrial and Masterstream Nozzle Stream Trajectory
4.0 FLUSHING DEBRIS
Debris in the water may get caught inside the nozzle. This trapped material will cause poor stream quality, shortened reach and
reduced flow. To remove debris trapped in the nozzle:
1)
Shut off flow to the nozzle.
2)
Move the stream shaper to the wide fog position.
3)
For Industrial Nozzle:
For Masterstream Selectable Gallonage Nozzle:
For Masterstream Fixed Gallonage Nozzle:
4)
Remove debris. Flow water to flush if necessary.
5)
Reassemble the nozzle. Tighten the baffle on the industrial nozzle to 30 ft-lbs (40 newton-meters).
WARNING
5.0 MAINTENANCE
Nozzles must be checked regularly to assure proper operation. Contact factory for parts lists and exploded views for particular
models.
6.0 WARRANTY
Task Force Tips, Inc., 2800 East Evans Avenue, Valparaiso, Indiana 46383 ("TFT") warrants to the original purchaser of its Industrial and
Masterstream series nozzles ("equipment"), and to anyone to whom it is transferred, that the equipment shall be free from defects in
material and workmanship during the five (5) year period from the date of purchase.
TFT's obligation under this warranty is specifically limited to replacing or repairing the equipment (or its parts) which are shown by
TFT's examination to be in a defective condition attributable to TFT. To qualify for this limited warranty, the claimant must return the
equipment to TFT, at 2800 East Evans Avenue, Valparaiso, Indiana 46383, within a reasonable time after discovery of the defect. TFT
will examine the equipment. If TFT determines that there is a defect attributable to it, TFT will correct the problem within a reasonable
time. If the equipment is covered by this limited warranty, TFT will assume the expenses of repair.
If any defect attributable to TFT under this limited warranty cannot be reasonably cured by repair or replacement, TFT may elect to
refund the purchase price of the equipment, less reasonable depreciation, in complete discharge of its obligations under this limited
warranty. If TFT makes this election, claimant shall return the equipment to TFT free and clear of any liens and encumbrances.
This is a limited warranty. The original purchaser of the equipment, any person to whom it is transferred, and any person who is an
intended or unintended beneficiary of the equipment, shall not be entitled to recover from TFT any consequential or incidental
damages for injury to person and/or property resulting from any defective equipment manufactured or assembled by TFT. It is agreed
and understood that the price stated for the equipment is in part consideration for limiting TFT's liability. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
TFT shall have no obligation under this limited warranty if the equipment is, or has been, misused or neglected (including failure to
provide reasonable maintenance) or if there have been accidents to the equipment or if it has been repaired or altered by someone
else.
THIS IS A LIMITED EXPRESS WARRANTY ONLY. TFT EXPRESSLY DISCLAIMS WITH RESPECT TO THE EQUIPMENT ALL
IMPLIED WARRANTIES OF MERCHANTABILITY AND ALL IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR
PURPOSE. THERE IS NO WARRANTY OF ANY NATURE MADE BY TFT BEYOND THAT STATED IN THIS DOCUMENT.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
TASK FORCE TIPS, Inc.
Made in USA • www.tft.com
©Copyright Task Force Tips, Inc. 1998-2004
HORIZONTAL DISTANCE (FEET)
30
40
50
A
B
80
100
120
140
160
HORIZONTAL DISTANCE (FEET)
Unscrew baffle using a 1-1/8 inch (28mm) socket.
Remove nozzle to gain access to debris.
Large amounts of debris may be unflushable and can reduce the flow of the nozzle resulting in an
ineffective flow. In the event of a blockage, it may be necessary to retreat to a safe area.
60
70
80
D
E
C
180
200
220
240
260
Turn flow selector on front of nozzle to "FLUSH" position.
2800 E Evans Ave • Valparaiso , IN 46383-6940 USA
800-348-2686 • 219-462-6161 • Fax 219-464-7155
GPM
CURVE
FLOW
90
A
B
C
20
D
E
1200
10
LPM
CURVE
FLOW
A
1200
B
1600
0
C
2300
280
300
D
3500
E
4500
LIM-035 October 5, 2004 Rev02
LBS
REACTION
310
200
430
280
610
400
920
600
780
KGF
REACTION
90
120
180
270
350
Advertisement
