Table of Contents
Advertisement
Quick Links
CONTENTS
Figures
Tables
1. GENERAL
Revision History
Features
• 2-wire deployment
• Repeaterless operation
• Bridged tap tolerant
• Span power for remote Total Reach DDS-R
termination unit
• Utilization in SLC Series 5 and Series 2000 channel
banks
61433105L2-5D
Trademarks: Any brand names and product names included in this document are trademarks,
Series 5 Total Reach DDS-DP
Total Reach All-Rate DDS Dataport
Installation and Maintenance
Figure 1
Section 61433105L2, Issue 4
registered trademarks, or trade names of their respective holders.
CLEI Code # 5SC531PF_ _
SW2
Figure 1. Series 5 Total Reach DDS-DP
• Loop Quality Monitor and A/B signaling options
• Bidirectional DS0 loopback capability
• Transmits Mux Out of Sync code upstream during
out of service loop condition.
• Embedded Digital System 6 capabilities for remote
provisioning, and performance monitoring.
Description
Section 61433105L2-5D
Issue 4, June 2000
DDS -DP
14331 05
SX
SYN C
NE
FE
QM
DSU
LBK
MAN
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ADTRAN DDS-DP
Summary of Contents for ADTRAN DDS-DP
-
Page 1: Installation And Maintenance
Trademarks: Any brand names and product names included in this document are trademarks, Series 5 Total Reach DDS-DP Installation and Maintenance Figure 1. Series 5 Total Reach DDS-DP • Loop Quality Monitor and A/B signaling options • Bidirectional DS0 loopback capability •... -
Page 2: Error Correction
SERIES 5 2-Wire Loop T-Carrier DDS-DP DDS-R T/R Pair Figure 2. Total Reach DDS Circuit Diagram NOTE The Series 5 Total Reach DDS-DP must be used with an appropriate Total Reach R unit. Options Table 1 19.2K SW56 ABSIG Figure 3. Option Switch... -
Page 3: Installation
SLC Series 5 BCU. These operating modes must be provisioned by enabling switches on SW2. A manual rate setting overrides BCU rate settings. The Series 5 Total Reach DDS-DP does not support 38.4 kbps. Signaling NOTE A/B signaling option is only applicable when SW56 is selected;... -
Page 4: Remote End Initiated Lbk Tests
NOTE If 64 kbps is selected, the unit will only respond to latching loopback sequences. Alternating sequences are not valid at this rate. Total Reach DDS-DP Bidirectional Loopback Support i t a , y t Figure 4. DS0 Bidirectional Loopback... -
Page 5: Control Protocol
: e l h t i t ' n t i b • Pressing the TROCU-R LBK pushbutton once will initiate a loopback at the TR DDS-DP towards the customer. See Figure 6. 61433105L2-5D Alternating MOS 9Ah/ASC 9Eh ASC 9Eh •... -
Page 6: Deployment Guidelines
ANSI T1.107-1995. NOTE Due to SLC Series 5 channel bank BCU constraints, provisioning of the Series 5 Total Reach DDS-DP may be viewed but not changed via Digital System 6. Out-of-Band Diagnostics ASC 9Eh Figure 6. Total Reach OCU-R Remote End Initiated Loopback, Local Loop ASC 9Eh Figure 7. -
Page 7: Maintenance
Table 5. Cable Type and Temperature Loss Data @ 13.3 kHz Table 6. Series 5 Total Reach DDS Insertion Loss Measurements NOTE The 50 dB AML limit includes 6 dB of signal margin to account for potential near-end cross talk (NEXT) from other digital services that may be provisioned in the same binder group. -
Page 8: Warranty And Customer Service
7. WARRANTY AND CUSTOMER SERVICE ADTRAN Carrier Networks Equipment Warranty, Repair, and Return Policy and Procedure, ADTRAN Sales ADTRAN Technical Support ADTRAN Repair/CAPS Repair and Return Address: Section 61433105L2, Issue 4 61433105L2-5D...
Need help?
Do you have a question about the DDS-DP and is the answer not in the manual?
Questions and answers