Page 2
Proluxe authorizes the original purchaser to return the product to the factory in Perris, procedures for your new Apex X1 California freight prepaid and only when the Dough Press. Please read this product, upon examination, has proven to be ...
S A F E T Y S U M M A R Y ● Voltage : 120/208/240 ● Amps : 12.5/11.05/5.94 ● Watts : 1500/2300/1500 Includes: 72” cord and NEMA approved plug. Warning Air Compressor Requirements: To reduce the risk of electrical shock, do not U.S.
3. C ounter – Cycle counter counts the number of applications from 1 to 9999 (see additional Notes – Counter). Caution Hot Avoid touching hot surfaces while operating 4. “ 2 Lower” (Fig. A) Refers to models using the machine. ...
Page 5
5. Swing open the lower platen and apply a quick spray of a good Tools Required: water based food release on the lower ● Food release platen. Proluxe offers its own food release spray NATURALLY CLEAR Model No. ● Soapy water solution 4 ...
Proluxe machines are relatively maintenance free. For a long lifespan, the following preventative maintenance should be followed: Daily Care: Apex X1 Troubleshoot Guide - Model #: DP1300 Problem Cause Action Ref # 5 ...
Page 7
Power Button on 1. Power cord is not plugged in. 1. Plug the power cord into wall Digital Controller receptacle and power button. 68 face is depressed but doesn’t turn on. 2. Circuit breaker is tripped off in the 2.
Page 8
by the overlay. Digital display shows 1. The relay on the switched side is 1. Replace the relay. 92 relay and particular not opening to regulate temperature. zone is overheating. Beeper not 1. Beeper on digital control board 1.
Page 9
under the lower instruction sheet and need to platen / Swing Arm order while Press is idle. P/N 110033 for the kit. Press does not close 1. Did not simultaneously press the 1. Try pressing both buttons 2 when pressing ...
Page 12
Apex X1 Part List - Model #: DP1300 ITEM DP1300A DP1300B 240 ~ DP1300TA 120 DP1300TB 240 DP1300TE 208 DP1300TGB DESCRIPTION 120 ~ AC ~ AC ~ AC ~ AC 240 ~ AC 1101025220 HOUSING, INSTRUMENT 11010252201...
Page 13
WASHER, THRUST 11059 11059 11059 11059 11059 11059 SCREW, ADJUSTMENT POST 11042 11042 11042 11042 11042 11042 THRUST PLATE 11058 11058 11058 11058 11058 11058 SCREW, SET 8-32 X 1" SST8321 SST8321 SST8321 SST8321 SST8321 SST8321 SCREW, SOCKET FLAT HEAD 1/4-20 X 3/4 SF142034 SF142034...
Page 16
SCREW, SET KNURLED CUP SST5161838 SST5161838K SST5161838K SST5161838K SST5161838K POINT 5/16-18 X 3/8 SST5161838KN ITEM DP1300A DP1300B 240 ~ DP1300TA 120 DP1300TB 240 DP1300TE 208 DP1300TGB DESCRIPTION 120 ~ AC ~ AC ~ AC ~ AC 240 ~ AC UPPER PLATEN WITH WIRING 11010253120 ONLY 110102531201...
APPROVED BY PROLUXE. IF THIS PROCEDURE IS NOT FOLLOWED, In no event shall Proluxe be liable for WARRANTY SERVICE WILL NOT BE consequential damages arising out of the COVERED. WARRANTY SERVICE WILL BE failure of any of its products if operated ...
Page 19
30 days. If upon inspection proper shipping documents immediately and by Proluxe or its authorized agent it is then file a claim for damages. determined the equipment has not been used ...
Need help?
Do you have a question about the Apex X1 and is the answer not in the manual?
Questions and answers