Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Condari Rangecraft RPN 90L-1
Summary of Contents for Condari Rangecraft RPN 90L-1
- Page 1 Rangecraft Rangehood Installation Instructions...
- Page 2 11. Rangecraft Rangehoods do not have the capacity to do the job over indoor barbecues,high speed gas burners or hotplates with a heat output rating over 40 megajoules. 12. Please contact Condari Pty Ltd to arrange an authorised technician to replace any cracked protective glass shields for the LED lights.
- Page 3 Installation instructions Rangecraft Rangehoods Fitted with Plasma-Norm Filter MODELS AVAILABLE UNDERCUPBOARD RPN 90L-1 290mm x 900mm Rangehood RPW 90L-1 330mm x 900mm Rangehood RPL 90L-1 430mm x 900mm Rangehood ISLAND RPD 50L-1 500mm Diameter Rangehood WALL MOUNTED RPB 100L-1 510mm x 1000mm Rangehood SPECIAL RANGECRAFT SP-RHP Made to order...
- Page 4 400cm Please note 400cm is the minimum opening requirement, Condari advises that the return air opening should be as large as practically possible for the application, to reduce the possibility of air noise from the air returning to the kitchen. The return air opening must be placed in a location that does not allow end user access to the Plasma Unit or Rangehood.
- Page 5 Installation instructions Rangecraft Rangehoods Fitted with Plasma-Norm Filter Maintaining your Plasma-Norm Rangecraft servicing should only be carried out by qualified persons. The Carbon Filter should be replaced every 5 years. If you notice any lingering odours this could indicate that the Carbon filter needs replacing. Please contact our Service Team to organise a service call to replace the Carbon Filter.
- Page 6 Installation instructions Rangecraft Rangehoods Fitted with Plasma-Norm Filter Undermount Rangecraft Rangehood Cut-Out dimensions PROUD MOUNT FLUSH MOUNT MODEL R/HOOD SIZE BASE SIZE CUT OUT DIMENSION CUT OUT DIMENSION RPN 90L-1 264 X 836 290 X 900 270 X 840 293 X 903 RPW 90L-1 294 X 880 330 X 900...
-
Page 7: Installation Instructions
Installation instructions Rangecraft Rangehoods Fitted with Plasma-Norm Filter Installation instructions • RPN / RPL / RPW 1. Loosen screws A & B by turning anti-clockwise. 2. Turn screw D anti clockwise until the head of the screw is raised this will extend the outer spring bracket to allow it to engage with the cabinetry. - Page 11 Installation instructions Rangecraft Rangehoods Fitted with Plasma-Norm Filter Installation instructions • RPD Remove Rangehood from packaging and place on a flat clean surface. Remove the filter. Remove the four screws in the corners of the base. Gently pull the base from the tube Once removed, the power supply and plasma plugs become visible.
- Page 13 Installation instructions Rangecraft Rangehoods Fitted with Plasma-Norm Filter Installation instructions • RPB Remove hood from packaging being careful not to touch stainless steel body. Locate centre of stove and using level or plumb line, mark centre line up to ceiling. Measure height of hood and mark same distance down from ceiling with level line.
-
Page 16: Operation Details
Stainless steel oil can also be used to further protect the finish. FILTER CLEANING For the best results, please clean filters regularly. Condari recommends cleaning filters once per month, or immediately after heavy use. You can do this by hand washing in warm soapy water, or by placing filters in the top rack of the dishwasher using a detergent of pH 8 or less. - Page 17 If there is a breach of this warranty, Condari will rectify, free of charge, at its nearest service centre or authorised service agency any fault caused by faulty workmanship or material at the time of manufacture occurring in the appliance within 36 months from the date of purchase of the appliance to the customer.
- Page 18 Fitted with Plasma-Norm Filter EXCLUSIONS There are some exclusions from the Condari Pty Ltd Guarantee. (on previous page) Rangecraft Rangehoods are not to be used over barbecues approved for outdoor use only. Outdoor barbecues will have a rating plate on them specifying that they are approved for outdoor use only and also a mega joule rating per burner or a total mega joule rating.
-
Page 19: Standard Warranty
The purchaser must fill in the above information and keep this with the original purchase document. This form must be produced if and when a claim is made under this warranty. QASAIR Rangehoods are made in Ringwood, Australia. Tel: +61 3 9482 7088 Fax: +61 3 9482 7011 Email: sales@condari.com.au... -
Page 20: Extended Warranty
EXTENDED WARRANTY Condari Pty Ltd provides an extended warranty of 72 months from the date of installation, if installed by an authorised Rangecraft installer and the form below is completed. The authorised installer also offers a warranty on their workmanship for the same period of 72 months with a guarantee that the installation is in compliance with ‘Qasair installation instructions’. - Page 21 Distributed in Australia by Condari Pty Ltd. T 1300 360 563 www.qasair.com.au www.condari.com.au Head Office VIC T 03 9482 7088 F 03 9482 7011 Email: sales@qasair.com.au NSW / ACT T 02 9316 4599 F 02 9316 9299 Email: salesnsw@qasair.com.au T 07 3423 3503 F 07 3282 9122 Email: salesqld@qasair.com.au...
Need help?
Do you have a question about the Rangecraft RPN 90L-1 and is the answer not in the manual?
Questions and answers