CaryMart S4PX-DC09 Manual

RF Wireless Remote Control Radio Controller / Transmitter & Receiver
Package Include:
1 x Receiver: S4PX-DC09 / S4PX-DC12 / S4PX-DC24 (4 Channel / Four Control Modes)
2 x Transmitter: C-4
1 x User manual
Features:
Wireless control, easy to install
With high power of 30A
Direct DC power output; control Lights, Motors, Fans, electrically operated Doors / Locks / Windows / Blinds / Cars or Other Appliances.
You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass
through walls, floors and doors.
With characteristics of reverse power protection and over current protection
Audible / visual indication
Use microcontroller model of EM78P156, an 8-bit microprocessor designed and developed with low-power and high-speed CMOS technology.
Use ULN2003 to drive relay, with strong anti-interference.
Reliable control: The transmitter (Encoding) and the receiver (Decoding) use an 8-bit code.
One/several transmitters can control one/several receivers simultaneously.
If you use two or more receivers in the same place, you can set them with different codes.
Transmitting Frequency: 315MHz / 433MHz
Receiver:
Model No.: S4PX-DC09 / S4PX-DC12 / S4PX-DC24
Channel: 4 CH
Control Modes: Toggle, Momentary, Latched, Momentary + Toggle
Coding Type: Fixed code
Coding Setting: By learning
Power Supply (Operating Voltage): DC12V±1V (S4PX-DC12), DC9V±1V (S4PX-DC09), DC24V±1V (S4PX-DC24)
Input / Output: DC 0~30V or AC 0~250V
Output voltage is same as Input voltage
PCB Size: 137mm x 80mm x 25mm
Case Size: 150mm x 90mm x 45mm
Maximum Working Current: 30A / each channel
Maximum Power: 270W/9VDC or 360W/12VDC or 720W/24VDC
Transmitter:
Model No.: C-4
Channel: 4 CH
Remote Control Distance: 100m / 300ft (theoretically)
Encode: Fixed code by soldering
Unit size: 58mm x 39mm x 16mm
Power Supply: 1 x 23A -12V battery (included, can be used for 12 months)
Usage:
Wire the dc power supply to terminal "＋" and "－" on the receiver. Wire the power supply of devices you want to control to the terminal Input.
Then wire the devices to the terminals A&B.
Setting different control modes (We have set the receiver as Toggle control mode before delivery. If you want to use other control modes, do as
following operation):
1) Setting control mode Toggle: Only connect Jumper-2.
Press button 1: Turn on the relay, terminal A&B of relay 1 output DC / AC power.
Press button 1 again: Turn off the relay, terminal A&B of relay 1 no output.
...
Press button 4: Turn on the relay, terminal A&B of relay 4 output DC / AC power.
Press button 4 again: Turn off the relay, terminal A&B of relay 4 no output.
2) Setting control mode Momentary: Only connect Jumper-1.
Press and hold button 1: Turn on the relay, terminal A&B of relay 1 output DC / AC power.
Release button 1: Turn off the relay, terminal A&B of relay 1 no output.
...
Press and hold button 4: Turn on the relay, terminal A&B of relay 4 output DC / AC power.
Release button 4: Turn off the relay, terminal A&B of relay 4 no output.
3) Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Press button 1: Turn on the relay, terminal A&B of relay 1 output DC / AC power.
Press other button: Turn off the relay, terminal A&B of relay 1 no output.
...
Press button 4: Turn on the relay, terminal A&B of relay 4 output DC / AC power.
SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: sale@carymart.com