AMX FG1052-13 Quick Start Manual

Overview
Component Video Distribution Amplifier Driver (DAD) Modules are available with
BNC or RCA connectors. The modules have either one input and two outputs for
1:2 distribution or one input and six outputs for 1:6 distribution of component video
signals. The single component video input is distributed to two or six outputs over
standard cable runs of up to 500 ft. (152.4 m) for YPbPr and up to 250 ft. (76.20 m) for
RGB with no additional equipment required. Each output can be independently
adjusted for gain and peaking to ensure the proper amount of compensation is
provided for each cable run. This guide contains complete information for this product.
RGB (BNC) Model FG1052-25
FIG. 1
Component Video DADs, 1:2 models
RGB (BNC) Model FG1052-28
YPbPr (RCA) Model FG1052-22
FIG. 2
Component Video DADs, 1:6 models
Product Specifications
General Specifications
Approvals Pending
Power* 1:2 model
Consumption (max.) +12 VDC to +24 VDC, 1A
Consumption (typical) +12 VDC, 400 mA
Connector 2.1 mm DC power jack
Power 1:6 model 100 to 240 VAC single phase, 50 - 60 Hz
Consumption (max.) 120 VAC, 650 mA
Consumption (typical) 120 VAC, 100 mA
Operational Temperature 32° to 110° F (0° to 43° C)
Humidity 0 to 90% non-condensing
Dimensions 1:2 model 5.15 in. (13.08 cm) depth
4.35 in. (10.92 cm) width
1.66 in. (4.22 cm) height without feet, 1 RU on rack shelf
Approximately 1.3 lb. (0.6 kg) weight
Dimensions 1:6 model 5.15 in. (13.08 cm) depth
17.40 in. (44.20 cm) width without rack ears
19.00 in. (48.26 cm) with ears
1.72 in. (4.37 cm) 1 RU height without feet
Approximately 4.5 lb. (2 kg) weight
Connector Type BNC, RCA
* The Component Video 1:2 DAD module uses a power supply that is provided with
the unit.
RGB & YPbPr Signal Specifications
Frequency Response
Signal to Noise Ratio Vin = 0.7 V, 100% IRE
Level
Input (max.)
Output (max.)
Impedance
Input
Output
Return Loss
Connector Type
AutoPatch Component Video (BNC & RCA) DAD Modules
YPbPr (RCA) Model FG1052-19
** Gain and Peaking are independent switches that allow the user to turn on or off the
gain and peaking.
Installation
Mounting Options
1:2 Models
Desktop
V Style Rack Mounting
versatile modules (contact your AMX representative).
1:6 Models
Desktop
Rack Mounting
To rack mount a 1:6 module:
1.
2.
FIG. 3
3.
±3 dB, 450 MHz or better
>65 dB
±1.75 V
±1.75 V
75 ohms
75 ohms
-45 dB @ 5 MHz
BNC, RCA
RGB Gain & Peaking** Specifications
Gain
OFF Unity
ON +0.85 dB
Peaking
OFF No peaking
ON 8 dB @ 150 MHz
8 dB @ 300 MHz
Cable Length (max.) 250 ft. (76.20 m)
YPbPr Gain & Peaking** Specifications
Gain
OFF Unity
ON +0.85 dB
Peaking
OFF No peaking
ON 9 dB @ 37.5 MHz
9 dB @ 80 MHz
Cable Length (max.) 500 ft. (152.4 m)
– Attach the rubber feet (included) to the bottom of the module.
– Mounting brackets and rack trays are available for these
– Attach the rubber feet (included) to the bottom of the module.
Remove one screw from each side of DAD (FIG. 3) Do not reuse for rack ear.
Attach the rack ears as shown in FIG. 3 (screws provided).
Remove screw
Remove screw (do not re-use) & attach rack ears
Place the module in a standard EIA 19 in. (48.26 cm) rack and secure it to rack
with screws.
Quick Start Guide