Savant AMP-2000 Series Quick Reference Manual

Savant 16 Channel Amplifier
Quick Reference Guide
Box Contents
(1) Savant 16 Channel Amplifier (AMP-2000-xx or AMP-2000I-xx)
(2) Rack Mounting Brackets
(8) Pan Head Screws (M3 x 8 mm)
(1) AC Power cord - 6 ft
(8) 4-pin Speaker Connectors
(4) Rubber Chassis Feet
(1) Trigger Cable - 2.5 mm (3/32") Mono to 3.5 mm (1/8") Mono
(1) Quick Reference Guide (this document)
Specifications
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 80% Relative Humity (non-condensing)
Cooling 202 cubic feet per minute (CFM) recommended
BTU 3925 BTU/hr
Dimensions and Weights
5.21 in (132.3 mm)
Height
Width 17.30 in (439.4 mm)
Depth 15.00 in (382.0 mm)
Weight Shipping: 44lb (19.5 kg)
Power
120V AC 10A 60 Hz - AMP-2000-00 (N. America)
Input Power
230V AC 5A 50 Hz - AMP-2000I-00 (International)
T15AH/250V (120V) (N. America)
Fuse Rating
T8AL/250V (230V) (International)
Maximum
1150 watts
Power
Operation Parameters
40 WPC at 8 ohms, 50 WPC at 4 ohms;
Rated Power
(0.1% THD+N, 1kHz)
Input
33k ohms
Impedance
Input
750mV for 40W at 8 ohms
Sensitivity
Overall
27.5dB
Voltage Gain
Frequency
Bandwidth limited from 20Hz to 20kHz +0.8dB
Response
Distortion, < 0.07% THD+N from 20Hz to 20kHz,
THD+N All channels driven at 8 ohms (1 Watt)
Signal-to-
>90dB
Noise Ratio
Input Triggers 3-24V AC/DC 5mA
Output
12V DV 100mA
Triggers
Compliance
Safety and
FCC Part 15 | UL-60065
Emissions
RoHS Compliant
Minimum Support Release
Savant OS da Vinci 5.1.1
AMP-2000-00/AMP2000I-00 | 009-0421-05 | 161127
Copyright© 2016 Savant Systems, LLC
Front Panel
Power Button
(Master)
Protection Status
Indicators (LED)
Power LED
Item Description
Power Button Turns the amplifier On or Off
(Master) See Setting the Amplifiers Turn On Mode for details.
Power LED Indicates the power state of the amplifier:
Off: No power is supplied to the amplifier.
Red: Amplifier is in Standby Mode.
Green: Amplifier is On.
Protection Status LED of each zone.
Off: The central potential protection mode has not
Status
Indicators been enabled.
(LED) Red: The central potential protection mode has
been enabled to protect a zone/channel.
See Protection Modes for details.
Rear Panel
Gain
Turn-on Mode Switch
Trigger Input
Control Output
Item Description
Turn-on Mode Three options for controlling power.
Switch – Constant (manual turn-on via the front panel
master Power button)
– Audio Sense
– 3-24 AC/DC Voltage Trigger (External)
See Setting the Amplifiers Turn On Mode for details.
Trigger Input 3-24V AC/DC - 3.5 mm (1/8") Mono jack
Turn-on Mode switch is set to 3-24 AC/DC Voltage
Trigger mode.
Control 12V DC 100mA - 2.5 mm (3/32") Mono jack
Output Used to trigger another device that is activated by
receiving a 12VDC 100mA signal.
See External Trigger Connections for details
Gain Independent gain controls allowing for fine tuning
the output level of each. channel.
Audio Inputs RCA Stereo (L&R) line-level analog audio inputs.
Speaker 4-pin Speaker Connectors
Connections NOTE: Compatible with 8 ohm or 4 ohm speakers.
Power Input IEC 320 power connector with 3-pole
detachable power cord.
Fuse T15AH/250V (120V) (N. America)
T8AL/250V (230V) (International)
For Product Info
Audio Input
Speaker Connections
45 Perseverance Way, Hayannis, MA 02601
Savant.com | 508.683.2500
Power
Input
Fuse