Download Print this page

Advertisement

Quick Links

INCLUDES: 2-SIDED SHOWERS AND 3-SIDED ALCOVE DOORS
Important!
1. When you receive your Newline shower check contents for any freight damage.
2. Advise Newline on 0508 639 5463 if any damage has occurred or a defect
identified within 8 hours of receiving the goods so this can be rectified.
3. Do not proceed with installation until resolved.
May 2020
Rhine Pivot
Low Profile Tray Series
INSTRUCTION MANUAL

Advertisement

loading
Need help?

Need help?

Do you have a question about the Rhine Pivot Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for NewLine Rhine Pivot Series

  • Page 1 1. When you receive your Newline shower check contents for any freight damage. 2. Advise Newline on 0508 639 5463 if any damage has occurred or a defect identified within 8 hours of receiving the goods so this can be rectified.
  • Page 2: Warranty

    PIVOT DOOR SETS 2-SIDED & ALCOVE APPLICATIONS WARRANTY Faulty goods are covered under warranty. Visit www.newline.co.nz for warranty information. Breakages incurred during construction are not covered under warranty. Installations must conform to the instructions to be covered by the warranty.
  • Page 3: Preparation Checklist

    PREPARATION CHECKLIST 2-Sided Shower: Ensure the floor is level and the walls are plumb and flat. Position all framing for solid fixing for the shower tray, shower and plumbing fittings. Wall profiles require a stud centred 20mm back from tray outside edge. Ensure all plumbing items have been installed prior to the lining being attached.
  • Page 4 PIVOT 2-SIDED SHOWER COMPONENT LIST Wall Channel K7119 Handle Back Door Seal K7072 Back Door Seal Stop Pivot Block K2004 All doors except 1200 K4000 Lower door seals Replacement Screw Pack - 2 & 3-Sided Chrome & White K2271 K6808 Wall Plug (Concrete) 4x35mm Screws Screw Caps...
  • Page 5 Apply silicone bead down back of channel prior to fastening. Refer to Page 3 Table A & B will give measurements for your specific installation. Acrylic Shower Layout Ensure you read “BEFORE YOU START” section on page 3. Mark wall profile. Fasten wall profiles for return and door panels.
  • Page 6 Fit return panel. Ø3.2mm • Connect door set to return panel. • NOTE: Table on page 3 will show suggested corner post position for your specific shower install. • Fasten this join parallel at corner. • Corner post must be plumb for alignment of magnetic seal.
  • Page 7 Apply silicone to join as indicated. Seal the join between wall profile and frame. 150mm up from base on both sides.
  • Page 8 PIVOT 3-SIDED ALCOVE SHOWER COMPONENT LIST: 3-SIDED ALCOVE Wall Channel K7102 Back Door Seal K7072 Back Door Seal Stop Lower Door Seals Pivot Block K2004 All doors except 1200 K4000 K6808 Replacement Screw Pack - Chrome & White K2271 Handle 1200 Door Wall Plug (Concrete) 4x35mm Screws...
  • Page 9 Wall Channel Adjustment: Pivot 3-Sided Alcove Shower Table Includes Low Profile (L/P) Tray applications NOMINAL TRAY TRAY TYPE TRAY ACTUAL WIDTH LINER TO LINER SCREEN MIN-MAX EXTENSION AT WALL SIZE (+/- 1mm) MEASUREMENT 2-SIDES OF FRAME 812mm 786mm 769mm - 784mm 8.5mm 902mm 876mm...
  • Page 10 Apply silicone bead down back of channel prior to fastening. Layout Mark wall profile holes both sides. Predrill liner with 2mm bit. Fasten wall profiles.
  • Page 11 1. Plumb and square up door to frame. 2. Adjust evenly to both wall profiles. Fasten door frame to wall profiles. Door seal full width of door. Notch out glass flange by 12mm each end of door. Trim each side of pivot.
  • Page 12 Apply silicone to outer join as indicated. Seal the join between wall profile and frame, 150mm up from base on both sides. CONTACT Freephone: 0508 639 5463 Phone: 09 444 2053 Fax: 09 443 0044 Email: info@newline.co.nz www.newline.co.nz...