Advertisement
Quick Links
INCLUDES: 2 SIDED SHOWERS AND 3 SIDED ALCOVE 900 / 1000 / 1200 DOORS
Important!
1. When you receive your Newline shower check contents for any freight damage.
2. Advise Newline on 0508 639 5463 if any damage has occurred within 8 hours of
receiving the goods so this is can rectified.
3. Do not proceed with installation until resolved.
December 2018 V2
Pivot Shower
INSTRUCTION MANUAL
Advertisement
Related Manuals for NewLine 900
Summary of Contents for NewLine 900
- Page 1 Important! 1. When you receive your Newline shower check contents for any freight damage. 2. Advise Newline on 0508 639 5463 if any damage has occurred within 8 hours of receiving the goods so this is can rectified. 3. Do not proceed with installation until resolved.
-
Page 2: Warranty
PIVOT DOOR SETS 2 SIDED & ALCOVE APPLICATIONS WARRANTY Faulty goods are covered under warranty for 5 years. Visit www.newline.co.nz for warranty information. Breakages incurred during construction are not covered under warranty. Installations must conform to the instructions to be covered by the warranty. -
Page 3: Before You Start
INDEX Page 4 - 2 Sided Shower Page 8 - 3 Sided Alcove Shower PREPARATION CHECKLIST PREPARATION CHECKLIST ENSURE YOU TICK THE SPECIFIC BOXES THAT APPLY AS YOU PROGRESS 2 Sided Shower: Ensure the floor is level and the walls are plumb and flat. Position all framing for solid fixing for the shower tray, shower and plumbing fittings. - Page 4 COMPONENT LIST: RETURN PANEL Wall Channel K7102 Handle Back Door Seal K7072 Magnet Stop K3829 Pivot Block K2004 900 & 1000 Door Lower door seals Replacement Screw Pack - 2 & 3 Sided Chrome & White K2271 K6808 Wall plug 4x35mm Screws Washer &...
- Page 5 Walls out of Plumb will not allow for Full minimum / maximum options. Apply silicone bead down back of channel prior to fastening. Refer to Page 3 Table A & B will give measurements for your specific installation. Acrylic Shower Lay-out Ensure you read “Before you start”...
- Page 6 Fit return panel • Connect door set to return panel • Finally adjust shower door in wall profiles and square up doors. • Drill and fasten the corner profile. (Additional adjustment is available at • Drill and fasten door frame to wall corner if needed) profile...
- Page 7 Apply silicone to join as indicated Seal the join between wall profile and frame. 150mm up from base on both sides...
- Page 8 COMPONENT LIST: 3 SIDED ALCOVE Wall Channel K7102 Back Door Seal K7072 Magnet Stop K3829 Pivot Block K2004 Lower door seals K6808 900 & 1000 Door Replacement Screw Pack - Chrome & White K2271 Handle 1200 Door Wall plug 4x35mm Screws Washer &...
- Page 9 Shower Type Wall Channel Adjustment 900mm 870mm (minimum) to 890mm (maximum) 1000mm 970mm (minimum) to 990mm (maximum) 1200mm 1170mm (minimum) to 1190mm (maximum) Walls out of Plumb will not allow for Full minimum / maximum options. Fit seal to back of door channel and fasten end caps (05) to top and bottom.
- Page 10 Apply silicone bead down back of channel prior to fastening. Layout Mark wall profiles Fasten wall profiles...
- Page 11 Square up door set and adjust to wall profiles. Fasten frame to wall profiles as indicated. Fasten details up the door and install bottom seal.
- Page 12 Apply silicone to outer join as indicated Seal the join between wall profile and frame. 150mm up from base on both sides...
- Page 13 CONTACT Freephone: 0508 639 5463 Phone: 09 444 2053 Fax: 09 443 0044 Email: info@newline.co.nz www.newline.co.nz...
Need help?
Do you have a question about the 900 and is the answer not in the manual?
Questions and answers